Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P013611  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground  


DESCRIPTION

In order to obtain a high purification rate for the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel ratio. The heated oxygen sensor (sensor 2) has the characteristic whereby its output voltage changes suddenly in the vicinity of the stoichiometric air fuel ratio. This is used to detect the oxygen concentration in the exhaust gas and provide the ECM with feedback to control the air fuel ratio. When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas increases. The heated oxygen sensor (sensor 2) informs the ECM of the lean condition (low voltage, i.e. less than 0.45 V). When the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is reduced, and the heated oxygen sensor (sensor 2) informs the ECM of the rich condition (high voltage, i.e. more than 0.45 V). The ECM judges, using the voltage output of the heated oxygen sensor (sensor 2), whether the air fuel ratio is rich or lean and controls the injection time accordingly. If a malfunction of the heated oxygen sensor (sensor 2) causes an output of abnormal voltage, the ECM is unable to perform accurate air fuel ratio control. The heated oxygen sensor (sensor 2) includes a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), a current flows to the heater in order to heat the sensor for accurate oxygen concentration detection.

A313385E01
2.313,2.25 2.5,2.25 false 1.667,1.74 2.115,2.167 true 2.542,2.198 3.052,2.417 0.51,0.219 10 false Cover 0.75,2.417 1.677,2.656 0.927,0.24 10 false Exhaust Gas 1.115,1.667 1.677,1.833 0.563,0.167 10 false Element 3.219,1.292 4.396,1.688 1.177,0.396 10 false Output Voltage 4.083,2.229 6.083,2.49 2,0.26 10 false Richer - Air Fuel Ratio - Leaner 4.49,0.177 6.031,0.385 1.542,0.208 10 false Ideal Air Fuel Mixture

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P013611 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground

All of the following conditions are met (3 trip detection logic):

(a)

Fuel-cut operation is not being performed.

(b)

Purge control* of the catalyst is not being performed.

(c)

Heated oxygen sensor (sensor 2) output voltage is less than 0.06 V.

(d)

Conditions (a), (b) and (c) are met for 5 seconds or more.

(e)

Active air-fuel ratio control is performed as follows after condition (d) is met:

(1)

Pulse signal is applied to heated oxygen sensor (sensor 2) signal line.

(2)

Difference in heated oxygen sensor (sensor 2) voltage before and after applying pulse signal is calculated.

(3)

Steps (1) and (2) are repeated 2 more times.


(f)

Average difference in heated oxygen sensor (sensor 2) voltage when active air-fuel ratio control is performed 3 times is less than 0.015 V.



·

Heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

ECM


Comes on DTC stored Engine B

HINT:

*: In order to purge oxygen adsorbed to the TWC, the stoichiometric ratio is controlled to rich side.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P013611)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P013611 is output A
P013611 and other DTCs are output B


HINT:

If any DTCs other than P013611 are output, troubleshoot those DTCs first.




A

2.INSPECT HEATED OXYGEN SENSOR (SENSOR 2)

B

GO TO DTC CHART

2.INSPECT HEATED OXYGEN SENSOR (SENSOR 2)

OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D85-4 (OX1B) - D50-124 (OX1B) Always Below 1 Ω
D85-2 (HT1B) - D50-24 (HT1B) Always Below 1 Ω
D85-3 (E1) - D50-123 (E12) Always Below 1 Ω
D85-4 (OX1B) or D50-124 (OX1B) - Body ground Always 10 kΩ or higher
D85-2 (HT1B) or D50-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013611)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013611)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Turn the GTS on.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
P013611 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B

END