Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P013613  O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open  


DESCRIPTION

Refer to DTC P013611.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P013611

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P013613 O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open

All of the following conditions are met (3 trip detection logic):

(a)

100 seconds have elapsed since heated oxygen sensor (sensor 2) dew point judgment* was completed.

(b)

Heated oxygen sensor (sensor 2) output voltage is between 1.25 and 3.5 V.

(c)

Conditions (a) and (b) are met continuously for 5 seconds.

(d)

Active air-fuel ratio control is performed as follows after condition (c) is met:

(1)

Pulse signal is applied to heated oxygen sensor (sensor 2) signal line.

(2)

Heated oxygen sensor (sensor 2) voltage is measured after pulse signal is applied.

(3)

Heated oxygen sensor (sensor 2) voltage after pulse signal applied is 2.8 V or higher.

(4)

When condition (3) is met, steps (1) and (2) are repeated 2 more times.


(e)

Average difference in heated oxygen sensor (sensor 1) output voltage when active air-fuel ratio control is performed 3 times is 2.8 V or higher.



·

Open in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)


Comes on DTC stored Engine A

HINT:

*: Condensation may form in the exhaust pipes after the engine is started and before the exhaust system has warmed up. If condensation exists, the sensor element may be damaged if the heated oxygen sensor (sensor 2) heater is heated excessively. Therefore, the ECM will restrict the output of the heated oxygen sensor (sensor 2) heater until it determines condensation is not forming in the exhaust pipes. Dew point judgment is when the ECM judges that condensation is no longer forming.


WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P013613 is detected when the vehicle is driven at an average vehicle speed of approximately 50 km/h (31 mph) in an urban area for approximately 30 minutes.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

The internal resistance of the heated oxygen sensor (sensor 2) cannot be measured using a tester.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (O2 SENSOR VOLTAGE B1S2)

Pre-procedure1

a.

Warm up the heated oxygen sensor (sensor 2) at an engine speed of 2500 rpm for approximately 3 minutes.


Procedure1

b.

Read the output voltage of the heated oxygen sensor (sensor 2) during racing the engine.

Powertrain > Engine > Data List
Tester Display
O2 Sensor Voltage B1S2
50003 372 218
Standard voltage:

Fluctuates between less than 0.4 V, and higher than 0.55 V (see the following figure).


A319417E01
1.24,1.313 2.156,1.51 0.917,0.198 10 false 0.55 V 1.313,1.625 2.229,1.823 0.917,0.198 10 false 0.4 V 1.427,1.948 1.76,2.135 0.333,0.188 10 false 0 V 1.427,0.99 1.802,1.188 0.375,0.198 10 false 1 V


Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

2.CLEAR DTC

NG

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
2.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P013613 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

B

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013613)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
P013613 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B

END

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D85-4 (OX1B) - D50-124 (OX1B) Always Below 1 Ω
D85-2 (HT1B) - D50-24 (HT1B) Always Below 1 Ω
D85-3 (E1) - D50-123 (E12) Always Below 1 Ω
D85-4 (OX1B) or D50-124 (OX1B) - Body ground Always 10 kΩ or higher
D85-2 (HT1B) or D50-24 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR