Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › 2020.07–2021.04
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal is input to the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns the transistor Tr in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr ON. Then, the fuel pump operates.

While the NE signal is input to the ECM with the engine running, the ECM turns the Tr on continuously.

WIRING DIAGRAM

A458579E01
0.646,0.635 1.104,0.833 0.458,0.198 10 false AM2 1.396,0.469 1.854,0.667 0.458,0.198 10 false H46 1.51,0.313 1.667,0.51 0.156,0.198 10 false 6 1.75,0.458 2.063,0.656 0.313,0.198 10 false +B 2.656,0.438 3.271,0.635 0.615,0.198 10 false IGPD 3.042,0.458 3.5,0.656 0.458,0.198 10 false H45 3.073,0.292 3.385,0.49 0.313,0.198 10 false 24 1.563,0.833 3.094,1.208 1.531,0.375 10 false Certification ECU (Smart Key ECU Assembly)*1 3.594,0.365 3.906,0.563 0.313,0.198 10 false *1 0.292,0.375 0.604,0.573 0.313,0.198 10 false *1 1.875,1.583 2.333,1.781 0.458,0.198 10 false AM1 0.76,1.833 1.219,2.031 0.458,0.198 10 false AM1 2.615,1.594 3.073,1.792 0.458,0.198 10 false IG1 1.708,1.573 1.865,1.771 0.156,0.198 10 false 7 2.885,1.594 3.042,1.792 0.156,0.198 10 false 8 0.385,1.573 0.698,1.771 0.313,0.198 10 false *2 3.479,1.594 3.792,1.792 0.313,0.198 10 false *2 1.323,1.958 1.781,2.156 0.458,0.198 10 false H54 1.302,2.125 4.823,2.323 3.521,0.198 10 false Ignition or Starter Switch Assembly*2 4.177,0.833 5.25,1.031 1.073,0.198 10 false from STA Signal Circuit 4.188,1.448 5.26,1.865 1.073,0.417 10 false from Crankshaft Position Sensor 5.698,0.844 6.156,1.042 0.458,0.198 10 false A55 5.708,1.365 6.167,1.563 0.458,0.198 10 false D50 5.781,0.688 6.094,0.885 0.313,0.198 10 false 46 5.76,1.177 6.073,1.375 0.313,0.198 10 false 78 5.771,1.531 6.083,1.729 0.313,0.198 10 false 79 5.708,1.688 6.167,1.885 0.458,0.198 10 false D50 6.052,0.854 6.51,1.052 0.458,0.198 10 false STA 6.052,1.375 6.51,1.573 0.458,0.198 10 false NE+ 6.052,1.698 6.51,1.896 0.458,0.198 10 false NE- 0.375,2.552 2.521,2.75 2.146,0.198 10 false INP STD NO.1-3 0.458,3.365 1.229,3.667 0.771,0.302 10 false BATT-MAIN NO.1 1.594,3.344 2.823,3.542 1.229,0.198 10 false IGP-MAIN 2.521,3.823 2.979,4.021 0.458,0.198 10 false IGP 2.26,3.125 2.417,3.323 0.156,0.198 10 false 3 2.948,3.115 3.104,3.313 0.156,0.198 10 false 5 2.26,3.458 2.417,3.656 0.156,0.198 10 false 2 2.938,3.458 3.094,3.656 0.156,0.198 10 false 1 3.25,3.354 3.708,3.552 0.458,0.198 10 false INJ 4.396,3.906 5.167,4.104 0.771,0.198 10 false C/OPN 4.208,3.125 4.365,3.323 0.156,0.198 10 false 2 4.948,3.115 5.104,3.313 0.156,0.198 10 false 1 4.198,3.49 4.354,3.688 0.156,0.198 10 false 3 4.927,3.5 5.083,3.698 0.156,0.198 10 false 5 5.708,3.229 6.167,3.427 0.458,0.198 10 false A55 5.771,3.052 6.083,3.25 0.313,0.198 10 false 59 6.052,3.229 6.365,3.427 0.313,0.198 10 false FC 2.698,5 4.688,5.198 1.99,0.198 10 false EFI-MAIN NO.2 1.896,4.438 3.885,4.635 1.99,0.198 10 false EFI-MAIN NO.2 2.75,4.198 2.906,4.396 0.156,0.198 10 false 3 3.438,4.198 3.594,4.396 0.156,0.198 10 false 5 2.729,4.677 2.885,4.875 0.156,0.198 10 false 2 3.438,4.667 3.594,4.865 0.156,0.198 10 false 1 4,5.604 4.156,5.802 0.156,0.198 10 false 5 3.292,5.594 3.448,5.792 0.156,0.198 10 false 3 3.281,5.917 3.438,6.115 0.156,0.198 10 false 2 4.01,5.938 4.167,6.135 0.156,0.198 10 false 1 1.51,5.854 3.5,6.052 1.99,0.198 10 false EFI-MAIN NO.1 3.281,6.313 5.271,6.51 1.99,0.198 10 false EFI-MAIN NO.1 2.719,7.396 2.875,7.594 0.156,0.198 10 false B 2.719,7.958 2.875,8.156 0.156,0.198 10 false E 3.24,7.365 3.698,7.563 0.458,0.198 10 false O22 3.24,7.531 4.01,7.76 0.771,0.229 10 false Fuel Pump 5.708,6.021 6.167,6.219 0.458,0.198 10 false A55 6.042,6.01 6.656,6.208 0.615,0.198 10 false MREL 5.854,5.844 6.01,6.042 0.156,0.198 10 false 9 0.552,7.688 1.167,7.885 0.615,0.198 10 false Battery 3.615,8.083 6.5,8.302 2.885,0.219 10 false *1: w/ Entry and Start System 3.625,8.427 6.615,8.635 2.99,0.208 10 false *2: w/o Entry and Start System 6.219,7.469 6.563,7.677 0.344,0.208 10 false ECM 2.76,7.188 2.917,7.385 0.156,0.198 10 false 4 2.729,8.208 2.885,8.406 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVE THE CIRCUIT RELAY)
a.

Enter the following menus.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 38

b.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVE THE CIRCUIT RELAY)

B

12.READ VALUE USING GTS (STARTER SW)
2.PERFORM ACTIVE TEST USING GTS (ACTIVE THE CIRCUIT RELAY)
a.

Enter the following menus.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 38

b.

Check whether the C/OPN relay operating sound occurs when performing the Active Test on the GTS.

Result:
Result Proceed to
C/OPN relay operating sound does not occur A
C/OPN relay operating sound occurs B




A

3.INSPECT C/OPN RELAY

B

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
3.INSPECT C/OPN RELAY

OK

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE C/OPN RELAY

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (C/OPN relay) - A55-59 (FC) Always Below 1 Ω
1 (C/OPN relay) or A55-59 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGP RELAY - C/OPN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGP RELAY - C/OPN RELAY)
a.

Remove the C/OPN relay and IGP relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - 2 (C/OPN relay) Always Below 1 Ω
5 (IGP relay) or 2 (C/OPN relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
A459384C04
0.115,0.177 0.427,0.375 0.313,0.198 10 false *1 1.104,1.938 1.417,2.135 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 C/OPN Relay


a.

Remove the C/OPN relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - Body ground IG ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT C/OPN RELAY

NG

10.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)
7.INSPECT C/OPN RELAY

OK

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPLACE C/OPN RELAY

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (C/OPN relay) - O22-4 (B) Always Below 1 Ω
5 (C/OPN RELAY) or O22-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FUEL PUMP

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the C/OPN relay and EFI-MAIN NO. 2 relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay) - 5 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
3 (C/OPN relay) or 5 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT EFI-MAIN NO. 2 RELAY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

12.READ VALUE USING GTS (STARTER SW)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Check the result when the ignition switch is ON and the cranking.

OK:
Condition Starter SW
Ignition switch ON OFF
Cranking ON



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (ENGINE SPEED)

NG

13.READ VALUE USING GTS (ENGINE SPEED)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

b.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT