Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P033525  Crankshaft Position Sensor "A" Signal Shape/Waveform Failure  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  


DESCRIPTION

The crankshaft position sensor system consists of a crank angle sensor plate (crankshaft) and a pickup coil*1 or MRE (Magnet Resistance Element) type sensor*2. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed to the crankshaft.

The crankshaft position sensor generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculated values, the fuel injection and ignition timing are controlled.

*1: w/o Stop and Start System

*2: w/ Stop and Start System


w/ Stop and Start System:

The crankshaft position sensor monitors the crankshaft position when the engine is stopped so that the engine can be restarted from the position that the crank was stopped. The crankshaft position sensor has a reverse rotation detection function, therefore the correct position of the crankshaft can be determined even if the crankshaft slightly rotates backwards. If the reverse rotation detection function malfunctions, stop and start control will be suspended.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P033525 Crankshaft Position Sensor "A" Signal Shape/Waveform Failure Either of the following condition is met (3 trip detection logic):
·

2 missing teeth position of crank angle sensor plate cannot be detected.

·

Position of teeth cannot be detected correctly.

·

Abnormal crankshaft position sensor signal pattern detected by crankshaft position sensor signal monitor IC (w/ stop and start system).


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (sensor plate)

·

ECM


Comes on DTC stored Engine A
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range Crankshaft position sensor signals are not received even though camshaft position sensor signals for 1 revolution are received (3 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (sensor plate)

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A427971E03
0.104,5.771 3.094,6.094 2.99,0.323 10 false Camshaft Position Sensor (for Intake Camshaft) 0.073,8 3.25,8.271 3.177,0.271 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.313,3.563 3.302,3.885 2.99,0.323 10 false Crankshaft Position Sensor*2 0.292,1.833 2.26,2.167 1.969,0.333 10 false Crankshaft Position Sensor*1 0.302,1.667 0.729,2.052 0.427,0.385 10 false D12 0.333,3.385 0.76,3.771 0.427,0.385 10 false D11 1.229,0.542 1.656,0.927 0.427,0.385 10 false VC 1.177,0.969 1.604,1.354 0.427,0.385 10 false NE+ 1.198,1.385 1.625,1.771 0.427,0.385 10 false NE- 1.229,2.583 1.656,2.969 0.427,0.385 10 false NE 1.208,3.125 1.635,3.51 0.427,0.385 10 false NE- 1.24,4.448 1.667,4.833 0.427,0.385 10 false VC 1.094,4.885 1.521,5.271 0.427,0.385 10 false VV1+ 1.104,5.323 1.531,5.708 0.427,0.385 10 false VV1- 1.167,6.698 1.594,7.083 0.427,0.385 10 false VC2 1.083,7.115 1.51,7.5 0.427,0.385 10 false VVE+ 1.083,7.542 1.51,7.927 0.427,0.385 10 false VVE- 0.125,5.604 0.552,5.99 0.427,0.385 10 false D9 0.104,7.833 0.531,8.219 0.427,0.385 10 false D10 5.104,8.063 5.719,8.448 0.615,0.385 10 false D50 5.583,8.073 6.198,8.458 0.615,0.385 10 false ECM 4.76,0.427 5.26,0.823 0.5,0.396 10 false VCNE 4.76,0.854 5.26,1.25 0.5,0.396 10 false NE+ 4.76,1.281 5.26,1.677 0.5,0.396 10 false NE- 4.75,2.583 5.25,2.979 0.5,0.396 10 false NE+ 4.76,3.146 5.26,3.542 0.5,0.396 10 false NE- 4.76,4.344 5.26,4.74 0.5,0.396 10 false VCG2 4.75,4.781 5.25,5.177 0.5,0.396 10 false G2+ 4.75,5.208 5.25,5.604 0.5,0.396 10 false G2- 4.75,6.583 5.25,6.979 0.5,0.396 10 false VCE1 4.75,7.01 5.25,7.406 0.5,0.396 10 false EV1+ 4.76,7.438 5.26,7.833 0.5,0.396 10 false EV1- 2.917,0.427 3.344,0.813 0.427,0.385 10 false *1 2.927,0.854 3.354,1.24 0.427,0.385 10 false *1 2.938,1.281 3.365,1.667 0.427,0.385 10 false *1 2.969,2.573 3.396,2.958 0.427,0.385 10 false *2 2.969,3.135 3.396,3.521 0.427,0.385 10 false *2 0.219,8.448 2.396,8.698 2.177,0.25 10 false *1: w/ Stop and Start System 2.396,8.448 4.573,8.698 2.177,0.25 10 false *2: w/o Stop and Start System 1.542,0.417 1.969,0.802 0.427,0.385 10 false 1 1.552,0.844 1.979,1.229 0.427,0.385 10 false 2 1.552,1.281 1.979,1.667 0.427,0.385 10 false 3 1.563,2.563 1.99,2.948 0.427,0.385 10 false 1 1.573,3.125 2,3.51 0.427,0.385 10 false 2 1.552,4.344 1.979,4.729 0.427,0.385 10 false 3 1.552,4.771 1.979,5.156 0.427,0.385 10 false 2 1.542,5.198 1.969,5.583 0.427,0.385 10 false 1 1.563,6.573 1.99,6.958 0.427,0.385 10 false 3 1.563,7 1.99,7.385 0.427,0.385 10 false 2 1.552,7.417 1.979,7.802 0.427,0.385 10 false 1 4.469,0.417 4.896,0.802 0.427,0.385 10 false 77 4.469,0.854 4.896,1.24 0.427,0.385 10 false 78 4.479,1.281 4.906,1.667 0.427,0.385 10 false 79 4.479,2.573 4.906,2.958 0.427,0.385 10 false 78 4.49,3.125 4.917,3.51 0.427,0.385 10 false 79 4.417,4.333 4.844,4.719 0.427,0.385 10 false 113 4.49,4.781 4.917,5.167 0.427,0.385 10 false 82 4.427,5.208 4.854,5.594 0.427,0.385 10 false 114 4.396,6.573 4.823,6.958 0.427,0.385 10 false 112 4.479,7.01 4.906,7.396 0.427,0.385 10 false 80 4.5,7.438 4.927,7.823 0.427,0.385 10 false 81

CONFIRMATION DRIVING PATTERN

DTC P033525 and P03352A is detected when the engine cranks more than 20 revolutions.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the crankshaft position sensor, throttle position sensor and accelerator pedal sensor assembly are output simultaneously, inspect the VC circuit of each component.



HINT:
·

After performing the inspection procedure for the crankshaft position sensor, if DTC P03352A is output again, check the following items related to the camshaft position sensor.

-

Installation condition of the camshaft position sensor

-

Installation condition of the camshaft

-

Connection of the camshaft position sensor connector


·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the values displayed on the GTS while the engine is running.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211
Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the crankshaft position sensor circuit.



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



Post-procedure1

c.

None.



A

B

2.INSPECT CRANKSHAFT POSITION SENSOR

C

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
2.INSPECT CRANKSHAFT POSITION SENSOR

OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D11-1 (NE) - D50-78 (NE+) Always Below 1 Ω
D11-2 (NE-) - D50-79 (NE-) Always Below 1 Ω
D11-1 (NE) or D50-78 (NE+) - Body ground Always 10 kΩ or higher
D11-2 (NE-) or D50-79 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION
B319222C02
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


a.

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR INSTALLATION

5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the crankshaft position sensor plate.

OK:

Crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.REPLACE CRANKSHAFT POSITION SENSOR

NEXT

7.CLEAR DTC
7.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525 OR P03352A)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525 OR P03352A)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
P033525 or P03352A is output B


Post-procedure1

c.

None.



A

END

B

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)

Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D12-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

10.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

16.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
10.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D12-2 (NE+) - D50-78 (NE+) Always Below 1 Ω
D12-3 (NE-) - D50-79 (NE-) Always Below 1 Ω
D12-2 (NE+) or D50-78 (NE+) - Body ground Always 10 kΩ or higher
D12-3 (NE-) or D50-79 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

11.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION
B319222C02
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


a.

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

12.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR INSTALLATION

12.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the crankshaft position sensor plate.

OK:

Crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

13.REPLACE CRANKSHAFT POSITION SENSOR

NG

13.REPLACE CRANKSHAFT POSITION SENSOR

NEXT

14.CLEAR DTC
14.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525 OR P03352A)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525 OR P03352A)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
P033525 or P03352A is output B


Post-procedure1

c.

None.



A

END

B

16.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

Pre-procedure1

a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D12-1 (VC) - D50-77 (VCNE) Always Below 1 Ω
D12-1 (VC) or D50-77 (VCNE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR