Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P244A00  Particulate Filter Differential Pressure Too Low Bank 1  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P244A00 Particulate Filter Differential Pressure Too Low Bank 1 After the differential pressure sensor characteristics diagnosis warm-up judgment is complete, the differential pressure sensor value is 0.5 kPa or less while the intake air volume is 80 kg/h or higher and fuel cut is not being performed (3 trip detection logic).
·

Front exhaust pipe assembly (GPF)

·

Differential pressure sensor

·

Wire harness or connector

·

Vacuum transmitting hose assembly

·

No. 1 vacuum pipe

·

Gas leak from exhaust system

·

Manifold Absolute Pressure Sensor

·

ECM


- DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

MONITOR DESCRIPTION

After the differential pressure sensor characteristics diagnosis warm-up judgment is complete, when the differential pressure sensor output value is below the threshold while the intake air volume is 80 kg/h or higher and fuel cut is not being performed, the system determines that the differential pressure sensor pipe is disconnected or the GPF is damaged or removed and the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


When the ambient temperature is 10°C or higher and the vehicle is driven for 15 minutes or more at a speed of 50 km/h or more, DTC P244A00 is detected.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244A00)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P244A00 is output A
P244A00 and other DTCs are output B


HINT:

If any DTCs other than P244A00 are output, troubleshoot those DTCs first.




A

2.CHECK FOR EXHAUST GAS LEAK

B

GO TO DTC CHART

2.CHECK FOR EXHAUST GAS LEAK
OK:

No gas leaks in exhaust system.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM PIPE)
A467273C01
1.479,1.5 2.49,0.552 2.49,0.552 2.677,0.552 true 1.365,2.063 1.615,3.146 1.615,3.146 1.823,3.146 true 4.031,2.729 4.729,1.01 4.729,1.01 5.01,1.01 true 4.021,3.24 2.917,4 2.917,4 2.635,4 true 4.656,4.5 3.719,5.302 3.719,5.302 3.5,5.302 true 2.729,0.479 3.042,0.677 0.313,0.198 10 false *1 1.875,3.063 2.188,3.26 0.313,0.198 10 false *2 5.063,0.917 5.375,1.115 0.313,0.198 10 false *1 2.458,3.927 2.771,4.125 0.313,0.198 10 false *2 3.333,5.219 3.646,5.417 0.313,0.198 10 false *3
*1 Differential Pressure Sensor *2 Vacuum Transmitting Hose Assembly
*3 No. 1 Vacuum Pipe - -


a.

Check the vacuum transmitting hose assembly is no exhaust gas leak between the differential pressure sensor and the vacuum pipe.

OK:

The vacuum transmitting hose assembly is no exhaust gas leak.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND VACUUM PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


Pre-procedure1

A467275C01
1.521,0.958 1.292,0.729 1.292,0.729 1.167,0.729 true 2.344,1.563 2.198,1.563 2.198,1.563 1.76,1.354 true 0.958,0.615 1.156,0.823 0.198,0.208 10 true *1 2.396,1.448 2.604,1.646 0.208,0.198 10 true *2
*1 Differential Pressure Sensor
*2 Vacuum Transmitting Hose Assembly


a.

Disconnect vacuum transmitting hose assembly on the differential pressure sensor.


b.

Start the engine.


Procedure1

c.

Check if there are exhaust gas pulsations from vacuum transmitting hose assembly during idling.


Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

OK

6.PERFORM DIFFERENTIAL PRESSURE SENSOR LEARNING

NG

17.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
6.PERFORM DIFFERENTIAL PRESSURE SENSOR LEARNING
a.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).


b.

Turn the ignition switch off and wait for 30 seconds or more (B).


c.

Repeat the above procedures (A) and (B) 3 times.

HINT:

Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.



Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
7.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the Intake Manifold Absolute Pressure value at ignition switch ON.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 80 and 110 kPa A
None of the above conditions are met B




A

8.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

8.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at idling.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 29 and 37 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

9.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
9.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 22 and 50 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

10.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

B

15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
10.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Check the value of Particulate Filter Differential Pressure Bank 1 at 4500 rpm without load.

Powertrain > Engine > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 372 1138
Result:
Result Proceed to
Particulate Filter Differential Pressure Bank 1 is below 1.0 kPa A
Except above B



Post-procedure1

c.

None.



A

11.CLEAR DTC

B

13.CLEAR DTC
11.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P244A00)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P244A00)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P244A00 is output A
DTCs are not output B



Post-procedure1

c.

None.



A

REPLACE FRONT EXHAUST PIPE ASSEMBLY (GPF)

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL

HINT:

Clear the GPF deposition values using the GTS after replacing the front exhaust pipe assembly (GPF).

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



B

13.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P244A00)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P244A00)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output



Result:
Proceed to
NEXT


Post-procedure1

c.

None.



NEXT

END

15.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D21-3 (VC) - D50-95 (VC2) Always Below 1 Ω
D21-1 (PIM) - D50-129 (PIM) Always Below 1 Ω
D21-2 (E2) - D50-127 (E21) Always Below 1 Ω
D21-3 (VC) or D50-95 (VC2) - Body ground Always 10 kΩ or higher
D21-1 (PIM) or D50-129 (PIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

16.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D21-3 (VC) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V
D21-1 (PIM) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

17.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D72-3 (VC) - A55-35 (VCPX) Always Below 1 Ω
D72-2 (PEX) - A55-34 (PEX) Always Below 1 Ω
D72-1 (E2) - A55-32 (EPEX) Always Below 1 Ω
D72-3 (VC) or A55-35 (VCPX) - Body ground and other terminals Always 10 kΩ or higher
D72-2 (PEX) or A55-34 (PEX) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

18.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.REPLACE DIFFERENTIAL PRESSURE SENSOR

Pre-procedure1

a.

None.


Procedure1

b.

Replace the differential pressure sensor.

HINT:

Click hereEngine / Hybrid System>1KR-FE (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL



Result:
Proceed to
NEXT


Post-procedure1

c.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).


d.

Turn the ignition switch off and wait for 30 seconds or more (B).


e.

Repeat the above procedures (A) and (B) 3 times.

HINT:

Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.




NEXT

END