Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432172 MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

C551 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51451A 3.REMOVE CENTER ENGINE UNDER COVER

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH

Hide 51441C 5.REMOVE ENGINE UNDER COVER RH

Hide 6.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 7.REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 8.REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55734A 9.REMOVE WATER GUARD PLATE RH (for LHD)

Hide 55735A 10.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55701J 11.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 12.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 13.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 15.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 17.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 57543C 18.REMOVE CENTER NO. 1 FLOOR BRACE (w/ Brace)

Hide 17410 19.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 20.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C433398N01
2.094,1.854 2.25,2.042 0.156,0.188 10 true A 2.635,1.104 2.792,1.292 0.156,0.188 10 true A 0.802,0.563 0.958,0.75 0.156,0.188 10 true B 2.01,0.229 2.167,0.417 0.156,0.188 10 true B

Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.


Hide 82121 21.SEPARATE ENGINE WIRE

a.
C439602

Disengage the 2 clamps.


b.

Disconnect the back-up light switch assembly connector.


c.

w/ Stop and Start System:

i.
C439603

Disconnect the neutral position switch connector.



d.

Remove the bolt and disconnect the engine wire.


e.

Remove the 2 bolts and separate the engine wire protector.


Hide 31461 22.REMOVE RELEASE CYLINDER HEAT INSULATOR

a.
C116852

Remove the 2 bolts and release cylinder heat insulator from the clutch release cylinder assembly.


Hide 31470 23.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C116850

Remove the 4 bolts to separate the clutch release cylinder assembly from the manual transaxle assembly.

NOTICE:
·

Suspend the clutch release cylinder assembly with a piece of rope so as not to place stress on the clutch line.

·

Do not depress the clutch pedal.




Hide 25.INSTALL ENGINE SUPPORT BRIDGE

a.
C425928C02
0.729,0.542 1.719,1.083 true 0.906,3.208 1.625,3.635 true 0.906,2.76 1.729,3.51 true 0.729,2.677 0.885,2.833 0.156,0.156 10 true *c 0.51,0.417 0.698,0.625 0.188,0.208 10 true *a 0.719,3.094 0.906,3.26 0.188,0.167 10 true *b
*a Existing Hole
*b Protective Tape
*c Bolt


Cover the existing holes in the left and right suspension tower with protective tape, then use a thin-bladed screwdriver to make holes in the tape, and insert the 2 bolts for setting the sub-beam of the engine support bridge.

Item Part No.
Bolt 9010-10226


b.

Install SST to the vehicle body as shown in the illustration.

C443680C01
1.375,1.333 1.594,1.042 true 5.177,1.354 4.958,1.104 true 1.469,5.281 1.854,5.115 true 1.844,6 2.135,6.229 true 4.938,4.771 5.323,5.094 true 4.385,5.927 4.719,5.813 true 1.896,5.021 2.104,5.188 0.208,0.167 10 true *a 2.125,6.156 2.333,6.344 0.208,0.188 10 true *b 1.156,1.313 1.354,1.51 0.198,0.198 10 true *c 5.198,1.292 5.396,1.49 0.198,0.198 10 true *c 4.74,4.667 4.927,4.865 0.188,0.198 10 true *a 4.167,5.823 4.375,6.01 0.208,0.188 10 true *b
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


SST
09940-10010  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




c.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


d.

Install the chain block to the sling bracket.

C443681C01
0.448,0.594 1.365,0.594 false 1.021,1.802 1.354,1.802 true 1.417,1.906 1.719,1.979 true 1.677,0.958 2.01,0.875 false 2.052,0.771 2.365,0.927 0.313,0.156 10 false *a 0.25,0.49 0.563,0.646 0.313,0.156 10 false *b 0.844,1.74 1.01,1.927 0.167,0.188 10 true *c 1.75,1.906 1.917,2.073 0.167,0.167 10 true *d
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



e.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with manual transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




f.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

C443682C01
1.74,0.917 1.417,0.698 true 2.271,1.458 2.573,1.208 true 1.094,1.563 1.427,1.354 true 1.104,2.25 1.448,1.979 true 0.938,4.24 1.333,4.375 true 1.573,4.354 1.885,4.604 true 0.948,3.646 1.292,3.385 true 0.719,4.125 0.917,4.302 0.198,0.177 10 true *2 2.052,1.365 2.271,1.563 0.219,0.198 10 true *a 1.208,0.604 1.396,0.771 0.188,0.167 10 true *b 0.875,1.49 1.083,1.667 0.208,0.177 10 true *c 1.917,4.552 2.104,4.74 0.188,0.188 10 true *b 1.313,3.281 1.531,3.479 0.219,0.198 10 true *a 0.896,2.198 1.094,2.375 0.198,0.177 10 true *1
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


NOTICE:

Connect the 1st link of the chain to the No. 1 engine hanger.



g.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.



h.
C330764C02
1.219,0.792 1.531,0.948 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) or more


Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.



i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

C443683C01
4,0.656 4.333,0.323 false 3.125,1.177 3.438,1.438 true 3.469,1.385 3.635,1.552 0.167,0.167 10 true *a 4.354,0.26 4.667,0.417 0.313,0.156 10 false *b 5.75,0.333 6.063,0.49 0.313,0.156 10 false *c 1.083,0.333 1.396,0.49 0.313,0.156 10 false *d 5.688,1.667 5.917,1.833 0.229,0.167 10 true *f 1.135,1.677 1.333,1.833 0.198,0.156 10 true *f 3,0.417 3.313,0.573 0.313,0.156 10 false *e 0.479,1.01 0.76,1.365 0.281,0.354 18 false i
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


CAUTION:
·

To prevent the engine with manual transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C399990C01
1.833,1.427 2.25,1.01 false 2.281,0.896 2.594,1.052 0.313,0.156 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with manual transaxle assembly and engine support bridge to fall, possibly causing serious injury.



NOTICE:
C330751

·

Do not perform any procedures if the chain of the chain block assembly is not straight.

·

When removing the engine mount, if the chain of the chain block assembly is not straight, the engine assembly or transaxle assembly may contact the vehicle body.




j.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

C443684C01
1.24,1.583 1.458,1.74 0.219,0.156 10 true *b 5.823,1.646 5.99,1.813 0.167,0.167 10 true *b 2.073,0.156 2.229,0.333 0.156,0.177 10 true *a 4.896,0.188 5.094,0.365 0.198,0.177 10 true *a 4.417,1 4.615,1.177 0.198,0.177 10 true *a 5.146,1.094 5.344,1.271 0.198,0.177 10 true *a 2.5,1.01 2.698,1.188 0.198,0.177 10 true *a 1.75,1.042 1.948,1.219 0.198,0.177 10 true *a
*a Wing Bolt *b Bolt


Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




k.
C443685C01
2.344,2.885 2.542,3.083 0.198,0.198 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with manual transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 51201 26.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 43409E 28.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C434059

Remove the 2 bolts and drive shaft heat insulator sub-assembly from the engine assembly.


Hide 30300 29.SUPPORT MANUAL TRANSAXLE ASSEMBLY

a.
C435438C01
1.865,0.865 1.344,0.865 true 1.156,0.76 1.333,0.938 0.177,0.177 10 true *a
*a Lashing Belt


Using a transmission jack and lashing belt or rope, support the manual transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely support the manual transaxle assembly.

·

Using a lashing belt or a rope, secure the manual transaxle assembly to the transmission jack.




Hide 12372A 30.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C435439

Disengage theclamp to separate the engine wire from the engine mounting insulator LH.


b.
C435440

Remove the 3 bolts, nut and engine mounting insulator LH from manual transmission case.


c.
C435441

Remove the 4 bolts, nut and engine mountinginsulator LH from the vehicle body.


Hide 33544C 32.REMOVE SHIFT LEVER DAMPER

a.
C242103

Remove the 2 nuts and shift lever damper from the manual transaxle assembly.


Hide 33.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C242360

Remove the 2 bolts and 2 wire harness clamp brackets from the manual transaxle assembly.


Hide 33111A 34.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C245766

Remove the manual transaxle case plug and gasket from the manual transaxle assembly.