Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for LHD) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0432676 AIR CONDITIONING UNIT(for LHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
No. 1 air conditioning radiator damper servo sub-assembly Initialize servo motor (Air Conditioning System) DTCs are stored for HV Model:
(Click here)
for Gasoline Model:
(Click here)
Air conditioning amplifier assembly
w/ Stop and Start System:
1.

Reset air conditioning information

2.

Learning of air conditioning information


Engine start function (Click here)
Initialize servo motor (Air Conditioning System) DTCs are stored for HV Model:
(Click here)
for Gasoline Model:
(Click here)

PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 51451A 2.REMOVE CENTER ENGINE UNDER COVER (for Full Cover Type)

Hide 3.DRAIN ENGINE COOLANT

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55734A 5.REMOVE WATER GUARD PLATE RH

a.
I116410

Disengage the claws to remove the water guard plate RH.


Hide 55815E 6.REMOVE NO. 1 FRONT VENTILATOR SEAL

a.
I116411

Disengage the claws to remove the No. 1 front ventilator seal.


Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
I116412

Disengage the clamp.


b.

Remove the 11 bolts and outer cowl top panel sub-assembly.

I116415


Hide 88707 8.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1KR-FE)

a.
I115659

Remove the bolt.


b.
I115660

Rotate the hook connector to disconnect the suction pipe sub-assembly as shown in the illustration.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 9.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (except 1KR-FE)

a.
I115661

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710G 10.DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE)

a.
I116394

Remove the bolt.


b.
I115662

Rotate the hook connector to disconnect the No. 2 air conditioning tube and accessory assembly as shown in the illustration.


c.

Remove the 2 O-rings from the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 16290F 11.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
I115663

Slide the hose clip to disconnect the No. 3 water by-pass hose assembly.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the No. 3 water by-pass hose assembly and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the No. 3 water by-pass hose assembly.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 12.DISCONNECT INLET HEATER WATER HOSE

a.
I115664

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87211 14.REMOVE NO. 1 AIR DUCT

a.
I116416

Disengage the clamps.


b.

Remove the 2 bolts.


c.

Disengage the claws to remove the No. 1 air duct.


Hide 15.REMOVE STEERING COLUMN ASSEMBLY

Hide 55086A 16.REMOVE CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115786

Remove the clip.


b.

Disengage the clamp to remove the center heater to register duct sub-assembly.


Hide 55084E 17.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116417

Remove the clip.


b.

Disengage the clamp to remove the No. 1 heater to register duct sub-assembly.


Hide 55085 18.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116418

Remove the clip.


b.

Disengage the clamps to remove the No. 2 heater to register duct sub-assembly.


Hide 19.REMOVE FRONT SEAT ASSEMBLY LH

Hide 20.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58569D 21.REMOVE FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)

a.
I115789

Disengage the claw and guide to remove the front floor caution plate cover.


Hide 77306 22.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 87212G 23.REMOVE NO. 3 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115793

Disengage the claws to remove the No. 3 rear air duct.


Hide 87212J 24.REMOVE NO. 5 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115794

Disengage the claws to remove the No. 5 rear air duct.


Hide 58510D 25.SEPARATE FRONT FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)

a.

Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.

I116447


Hide 87212F 26.REMOVE NO. 2 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115792

Disengage the claws to remove the No. 2 rear air duct.


Hide 87212H 27.REMOVE NO. 4 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115795

Disengage the claws to remove the No. 4 rear air duct.


Hide 87212 28.REMOVE NO. 1 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115798

Disengage the claws to remove the No. 1 rear air duct.


Hide 58510D 29.SEPARATE FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)

a.

Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.

I116419


Hide 55216C 30.REMOVE NO. 4 DASH PANEL INSULATOR PAD

a.

Disengage the clips to remove the No. 4 dash panel insulator pad.

I116420


Hide 88539J 31.DISCONNECT DRAIN COOLER HOSE

a.
I115796

Disconnect the drain cooler hose.


Hide 83108 32.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 55308B 33.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 34.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 35.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)

Hide 55306A 36.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I115797C01
1.365,1.792 1.625,2.031 0.26,0.24 12 true *A
*A for Cold Area Specification Vehicles


Remove the bolt to disconnect the instrument panel wire.


b.

Disengage the clamps to disconnect the instrument panel wire.


c.

for Cold Area Specification Vehicles:

i.

Remove the ground wire bolt.


ii.

Disengage the guide to disconnect the ground wire.



d.

Remove the bolt, screw, nut and No.1 instrument panel brace sub-assembly.


Hide 82141 37.SEPARATE INSTRUMENT PANEL WIRE

a.
I115800

Disengage the clamps.


b.
I115806

Remove the 2 nuts and bolt to separate the instrument panel junction block assembly RH.


c.

for Manual Air Conditioning System Single Layer Type:

i.
I115811

Disconnect the 2 connectors.


ii.

Disengage the clamp.



d.

for Manual Air Conditioning System Double Layer Type:

i.
I115812

Disconnect the 3 connectors.


ii.

Disengage the clamps.



e.

for Automatic Air Conditioning System:

i.
I115810

Disconnect the connector.


ii.

Disengage the clamp.



f.

for Manual Air Conditioning System:

i.
I115814

Disconnect the connector.


ii.

Disengage the clamp.



g.

for Automatic Air Conditioning System:

i.
I116421

Disconnect the 2 connectors.


ii.

Disengage the clamp.



h.

Disconnect each connector.

I116422C01
4.385,4.365 4.635,4.604 0.25,0.24 12 true *A 1.563,0.74 1.76,0.938 0.198,0.198 10 true *a 0.896,1.146 1.094,1.344 0.198,0.198 10 true *a 5.906,0.167 6.104,0.365 0.198,0.198 10 true *a 5.292,0.625 5.49,0.823 0.198,0.198 10 true *a 3.417,0.698 3.615,0.896 0.198,0.198 10 true *b 0.865,2.792 1.063,2.99 0.198,0.198 10 true *b 0.99,3.292 1.188,3.49 0.198,0.198 10 true *b 1.448,3.573 1.646,3.771 0.198,0.198 10 true *b 1.198,2.76 1.396,2.958 0.198,0.198 10 true *b 1.802,2.708 2,2.906 0.198,0.198 10 true *b 2.594,2.792 2.792,2.99 0.198,0.198 10 true *b 1.99,3.031 2.188,3.229 0.198,0.198 10 true *b 4.021,2.542 4.219,2.74 0.198,0.198 10 true *b
*A for Cold Area Specification Vehicles - -
*a Guide *b Clamp



i.

for Cold Area Specification Vehicles:

i.

Disconnect the connector.



j.

Remove the 4 ground wire bolts.


k.

Disengage the guides to disconnect the 4 ground wires.


l.

Disengage each clamp to separate the instrument panel wire.


Hide 38.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the nut and 6 bolts.

I116423C01
0,0 0,0 false
V113147

Remove in this Direction - -



b.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 39.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly.

I116424