Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model LHD) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432221 BRAKE ACTUATOR(for HV Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


HINT:
w/ Electric Parking Brake System:

The parking brake indicator light blinks (red) when the ignition switch is turned on after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

a.

Install the 3 No. 1 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly with the 3 bolts.


b.
C436249N01
0.979,0.854 1.167,1.031 0.188,0.177 10 true 1 0.938,1.615 1.125,1.792 0.188,0.177 10 false 2 1.208,1.969 1.396,2.146 0.188,0.177 10 false 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44591 4.INSTALL NO. 1 BRAKE ACTUATOR BRACKET

a.

Install the No. 1 brake actuator bracket to the brake actuator bracket assembly with the 3 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.
C436253N01
0.271,1.115 0.49,1.313 0.219,0.198 10 true 1 2.823,1.646 3.042,1.844 0.219,0.198 10 true 2 1.323,1.938 1.542,2.135 0.219,0.198 10 true 3

Fully tighten the bolt and 2 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Return the suction pipe sub-assembly and air conditioner tube and accessory assembly to its original position.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.



d.
C436243C01
0.948,1.74 1.042,1.74 1.042,1.74 1.125,1.406 true 1.083,0.896 1.615,0.635 1.615,0.635 1.719,0.635 true 1.198,0.656 1.458,0.115 1.458,0.115 1.552,0.115 true 0.917,1.052 0.542,0.292 0.542,0.292 0.438,0.292 true 0.76,1.24 0.479,0.75 0.479,0.75 0.365,0.75 true 1.406,1.031 2.104,0.896 2.104,0.896 2.208,0.896 true 2.219,0.802 2.396,0.979 0.177,0.177 10 true *a 0.74,1.656 0.927,1.823 0.188,0.167 10 true *b 1.573,0.031 1.75,0.208 0.177,0.177 10 true *c 1.729,0.563 1.917,0.74 0.188,0.177 10 true *d 0.25,0.198 0.427,0.385 0.177,0.188 10 true *e 0.208,0.688 0.365,0.854 0.156,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


e.
C436254C01
1.698,3.042 2.01,3.198 0.313,0.156 10 false *a 1.458,0.458 1.635,0.615 0.177,0.156 10 true A 0.625,0.5 0.802,0.656 0.177,0.156 10 true A 0.458,0.865 0.635,1.021 0.177,0.156 10 true A 0.344,1.271 0.521,1.427 0.177,0.156 10 true A 0.969,1.677 1.146,1.833 0.177,0.156 10 true B 1.5,1.281 1.677,1.438 0.177,0.156 10 true B
*a Torque Wrench Fulcrum Length


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




f.
C436255C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 88710E 6.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
C436256C01
0,0 0,0 false
V113147

Install in this Direction


Connect the air conditioning tube and accessory assembly to the air conditioning unit assembly.


e.

Engage the clamp to install the air conditioning tube and accessory assembly.


Hide 88707 7.INSTALL SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
C436257

Connect the suction pipe sub-assembly to the air conditioning unit assembly.


e.

Engage the clamp to install the suction pipe sub-assembly.


f.
C436258C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the hook connector as shown in the illustration.


g.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 55701J 8.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 19.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 22. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART