Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for LHD) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0432676 AIR CONDITIONING UNIT(for LHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for LHD)  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

I116424


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I116441C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the 6 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Temporarily install the nut.

NOTICE:

Do not fully tighten the nut.



Hide 55306A 3.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

NOTICE:

Do not fully tighten the screw.



Hide 4.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten the 3 bolts, screws and nut in the order shown in the illustration to install the air conditioner unit assembly.

I116442N01
2.344,1.167 2.479,1.333 0.135,0.167 10 true 1 3.406,1.188 3.563,1.365 0.156,0.177 10 true 3 5.344,1.063 5.479,1.229 0.135,0.167 10 true 2 4.354,2.958 4.49,3.125 0.135,0.167 10 true 5 2.302,2.99 2.438,3.156 0.135,0.167 10 true 4

Torque:
Bolt : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 82141 5.INSTALL INSTRUMENT PANEL WIRE

a.

Engage the each clamp to install the instrument panel wire.

I116443C01
1.198,5.292 1.448,5.531 0.25,0.24 12 true *A 4.385,4.375 4.635,4.615 0.25,0.24 12 true *A 0.865,1.021 1.083,1.219 0.219,0.198 10 true *a 1.563,0.76 1.781,0.958 0.219,0.198 10 true *a 5.917,0.198 6.135,0.396 0.219,0.198 10 true *a 5.281,0.604 5.5,0.802 0.219,0.198 10 true *a 3.417,0.615 3.635,0.813 0.219,0.198 10 true *b 0.302,2.615 0.521,2.813 0.219,0.198 10 true *b 1.198,2.771 1.417,2.969 0.219,0.198 10 true *b 1.792,2.708 2.01,2.906 0.219,0.198 10 true *b 2.583,2.771 2.802,2.969 0.219,0.198 10 true *b 1.958,3.052 2.177,3.25 0.219,0.198 10 true *b 1.458,3.552 1.677,3.75 0.219,0.198 10 true *b 1,3.271 1.219,3.469 0.219,0.198 10 true *b 4.021,2.531 4.24,2.729 0.219,0.198 10 true *b 2,5.438 2.219,5.635 0.219,0.198 10 true *b 1.198,4.833 1.417,5.031 0.219,0.198 10 true *a 1.865,5.042 2.083,5.24 0.219,0.198 10 true *b
*A for Cold Area Specification Vehicles - -
*a Guide *b Clamp



b.

Connect the each connector.


c.

for Cold Area Specification Vehicles:

i.

Engage the guide to connect the ground wire with the bolt to the No. 1 instrument panel brace sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the connector.



d.

Connect the instrument panel wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Install the 4 ground wires with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

for Manual Air Conditioning System:

i.
I115814

Engage the clamp.


ii.

Connect the connector.



g.

for Automatic Air Conditioning System:

i.

Engage the clamp.


ii.
I116421

Connect the 2 connectors.



h.

for Manual Air Conditioning System Single Layer Type:

i.

Engage the clamp.


ii.
I115811

Connect the 2 connectors.



i.

for Manual Air Conditioning System Double Layer Type:

i.
I115812

Engage the clamps.


ii.

Connect the 3 connectors.



j.

for Automatic Air Conditioning System:

i.
I115810

Engage the clamp.


ii.

Connect the connector.



k.
I115806

Install the instrument panel junction block assembly RH with the 2 nuts and bolt.


l.
I115800

Engage the clamps.


Hide 6.INSTALL TELEMATICS TRANSCEIVER WITH BRACKET (w/ Telematics Transceiver)

Hide 7.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 55308B 8.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 83108 9.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 88539J 10.INSTALL DRAIN COOLER HOSE

a.
I115796

Connect the drain cooler hose.


Hide 55216C 11.INSTALL NO. 4 DASH PANEL INSULATOR PAD

a.

Engage the clips to install the No. 4 dash panel insulator pad.

I116444


Hide 87212 12.INSTALL NO. 1 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115798

Engage the claws to install the No. 1 rear air duct.


Hide 87212F 13.INSTALL NO. 2 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115792

Engage the claws to install the No. 2 rear air duct.


Hide 87212H 14.INSTALL NO. 4 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115795

Engage the claws to install the No. 4 rear air duct.


Hide 58510D 15.INSTALL FLOOR CARPET ASSEMBLY (for Cold Area Specification Vehicles)

a.

Install the front floor carpet assembly with the 2 clips as shown in the illustration.

I116445


Hide 87212G 16.INSTALL NO. 3 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115793

Engage the claws to install the No. 3 rear air duct.


Hide 87212J 17.INSTALL NO. 5 REAR AIR DUCT (for Cold Area Specification Vehicles)

a.
I115794

Engage the claws to install the No. 5 rear air duct.


Hide 58510D 18.INSTALL FRONT FLOOR CARPET ASSEMBLY (except Cold Area Specification Vehicles)

a.

Install the front floor carpet assembly with the 2 clips as shown in the illustration.

I116446


Hide 77306 19.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 58569D 20.INSTALL FRONT FLOOR CAUTION PLATE COVER (for Cold Area Specification Vehicles)

a.
I115789

Engage the guide and claw to install the front floor caution plate cover.


Hide 21.INSTALL FRONT SEAT ASSEMBLY LH

Hide 22.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55084E 23.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116417

Engage the clamp to install the No. 1 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55085 24.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116418

Engage the clamps to install the No. 2 heater to register duct sub-assembly.


b.

Install the clip.


Hide 55086A 25.INSTALL CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115786

Engage the clamp to install the center heater to register duct sub-assembly.


b.

Install the clip.


Hide 26.INSTALL STEERING COLUMN ASSEMBLY

Hide 87211 27.INSTALL NO. 1 AIR DUCT

a.
I116416

Engage the claws and clamps to install the No. 1 air duct.


b.

Install the 2 bolts.


Hide 87245 29.INSTALL INLET HEATER WATER HOSE

a.

for M15A-FKS:

i.
I115718C02
1.583,3.219 1.677,3.469 true 0.74,2.323 1.052,2.479 0.313,0.156 10 false *a 1.406,3.115 1.719,3.271 0.313,0.156 10 false *b 1.135,1.656 1.281,1.813 0.146,0.156 10 true A 1.385,2.771 1.75,2.948 0.365,0.177 10 false *c
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.




b.

except M15A-FKS:

i.
I116332C01
1.604,3.292 1.76,3.031 false 0.594,2.281 0.906,2.438 0.313,0.156 10 false *a 1.802,2.938 2.115,3.094 0.313,0.156 10 false *b 2.229,2.604 2.542,2.76 0.313,0.156 10 false *c 1.167,1.729 1.344,1.917 0.177,0.188 10 true A
*a View A
*b Marking
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

Paint Mark:
Engine Color
1KR-FE Yellow
M15A-FXE White


NOTICE:

Do not apply excessive force to the inlet heater water hose.




Hide 16290F 30.INSTALL NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
I115720C02
1.729,3.469 1.844,3.188 false 0.771,2.406 1.083,2.563 0.313,0.156 10 false *a 1.896,3.104 2.208,3.26 0.313,0.156 10 false *b 1.417,2.823 1.771,2.99 0.354,0.167 10 false *c 0.823,1.354 0.969,1.5 0.146,0.146 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


for M15A-FKS:

i.

Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the No. 3 water by-pass hose assembly.




b.

except M15A-FKS:

i.
I116333C01
1.708,3.281 1.583,3.042 false 0.198,2.292 0.51,2.448 0.313,0.156 10 false *a 1.406,2.917 1.719,3.073 0.313,0.156 10 false *b 0.833,2.667 1.146,2.823 0.313,0.156 10 false *c 0.74,1.375 0.917,1.552 0.177,0.177 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (120°)


Connect the No. 3 water by-pass hose assembly with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the No. 3 water by-pass hose assembly.




Hide 88716A 31.INSTALL COOLER REFRIGERANT LIQUID PIPE A (except 1KR-FE)

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

for Gasoline Model (HFC-134a(R134a)):

ND-OIL 8 or equivalent

for Gasoline Model (HFO-1234yf(R1234yf)):

ND-OIL 12 or equivalent

for HV Model:

ND-OIL 11 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 32.INSTALL SUCTION PIPE SUB-ASSEMBLY (except 1KR-FE)

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

Compressor Oil:

for Gasoline Model (HFC-134a(R134a)):

ND-OIL 8 or equivalent

for Gasoline Model (HFO-1234yf(R1234yf)):

ND-OIL 12 or equivalent

for HV Model:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
I115835

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 88710G 33.INSTALL NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE)

a.

Remove the vinyl tape from the No. 2 air conditioning tube and accessory assembly.


b.

Apply sufficient compressor oil to 2 new O-rings and fitting surface of the No. 2 air conditioning tube and accessory assembly.

Compressor Oil:

for HFC-134a(R134a):

ND-OIL 8 or equivalent

for (HFO-1234yf(R1234yf):

ND-OIL 12 or equivalent



c.

Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the No. 2 air conditioning tube and accessory assembly.


e.
I115836

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 55701J 34.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install outer cowl top panel sub-assembly with the 11 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
I116412

Engage the clamp.


Hide 55815E 35.INSTALL NO. 1 FRONT VENTILATOR SEAL

a.
I116411

Engage the claws to install the No. 1 front ventilator seal.


Hide 55734A 36.INSTALL WATER GUARD PLATE RH

a.
I116410

Engage the claws to install the water guard plate RH.


Hide 37.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 38.ADD ENGINE COOLANT

Hide 39.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 51451A 44.INSTALL CENTER ENGINE UNDER COVER (for Full Cover Type)

Hide 46.PERFORM REGISTRATION (w/ Stop And Start System)