Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model LHD) › 2020.07–2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432227 BRAKE ACTUATOR(for Gasoline Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the 3 brake actuator bracket cushions to the brake actuator bracket assembly.


b.

Install the 3 No. 1 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.



Hide 44510 2.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly with the 3 bolts.


b.
C436294E01
3.052,0.813 3.208,1.01 0.156,0.198 10 false 1 1.469,0.604 1.625,0.802 0.156,0.198 10 true 2 2,1.771 2.156,1.969 0.156,0.198 10 false 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 3.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C436296E01
0.292,0.75 0.448,0.948 0.156,0.198 10 true 1 1.521,1.969 1.677,2.167 0.156,0.198 10 true 3 2.885,1.719 3.042,1.917 0.156,0.198 10 true 2

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.

Fully tighten the bolt and 2 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

for M15A-FKS:

i.
C436291

Engage the clamp and install a new No. 1 brake tube clamp to the vehicle body.


ii.
C436290

Engage the 5 clamps to install the No. 1 brake tube clamp to the brake lines.


iii.
C436289

Engage the 5 clamps to install a new No. 2 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.




d.
C436287C01
1.969,0.74 2.323,0.313 2.323,0.313 2.417,0.313 true 1.052,1.781 1.156,1.781 1.156,1.781 1.5,1.354 true 2.146,1.031 2.615,0.792 2.615,0.792 2.708,0.792 true 0.656,0.76 0.76,0.76 0.76,0.76 1.354,1 true 1,0.313 1.104,0.313 1.104,0.313 1.542,0.896 true 1.76,0.802 1.885,0.094 1.885,0.094 1.979,0.094 true 2.719,0.677 2.885,0.833 0.167,0.156 10 true *a 0.865,1.677 1.031,1.833 0.167,0.156 10 true *b 0.469,0.656 0.635,0.813 0.167,0.156 10 true *c 0.823,0.208 0.99,0.365 0.167,0.156 10 true *d 1.99,0 2.156,0.156 0.167,0.156 10 true *e 2.427,0.219 2.594,0.375 0.167,0.156 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




e.
C436297C01
2.719,2.656 2.802,3.052 2.802,3.052 2.896,3.052 false 1.75,3.052 2.063,3.208 0.313,0.156 10 false *a 2.927,2.969 3.24,3.125 0.313,0.156 10 false *b 1.177,1.688 1.323,1.844 0.146,0.156 10 true B 2.573,1.115 2.719,1.271 0.146,0.156 10 true B 2.365,0.802 2.51,0.958 0.146,0.156 10 true A 1.688,1.302 1.833,1.458 0.146,0.156 10 true A 1.167,0.396 1.313,0.552 0.146,0.156 10 true A 0.792,0.771 0.938,0.927 0.146,0.156 10 true A
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 6 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

(B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




f.
C436298C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




g.

for M15A-FKS:

i.

Return the suction pipe sub-assembly and air conditioner tube and accessory assembly to its original position.

NOTICE:

Do not apply excessive force to the suction pipe sub-assembly and air conditioner tube and accessory assembly.




Hide 88710E 4.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for M15A-FKS)

a.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:
HFC-134a (R134a):

ND-OIL 8 or equivalent

HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



c.

Install the O-ring to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
C436301C01
0,0 0,0 false
V113147

Install in this Direction


Connect the air conditioning tube and accessory assembly to the air conditioning unit assembly.


e.

Engage the clamp to install the air conditioning tube and accessory assembly.


Hide 88707 5.INSTALL SUCTION PIPE SUB-ASSEMBLY (for M15A-FKS)

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:
HFC-134a (R134a):

ND-OIL 8 or equivalent

HFO-1234yf (R1234yf):

ND-OIL 12 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
C436302

Connect the suction pipe sub-assembly to the air conditioning unit assembly.


e.

Engage the 2 clamps to install the suction pipe sub-assembly.


f.
C436303C01
0,0 0,0 false
V113147

Rotate in this Direction


Rotate the hook connector as shown in the illustration.


g.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 55225C 6.INSTALL DASH PANEL HEAT INSULATOR (for M15A-FKS)

a.
C436282E01
1.729,0.229 1.885,0.427 0.156,0.198 10 true A 2.677,0.438 2.833,0.635 0.156,0.198 10 true A

Temporarily install the dash panel heat insulator to the vehicle body with the 2 nuts (A).

i.
C436281E01
1.042,1.427 1.188,1.583 0.146,0.156 10 true B

Install the nut (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Tighten the 2 nuts (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51451A 7.INSTALL CENTER ENGINE UNDER COVER (for M15A-FKS)

Hide 55701J 8.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 11.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 19.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for M15A-FKS)

Hide 21.INSPECT FOR REFRIGERANT LEAK (for M15A-FKS)

Hide 22. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART