Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422055 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly
1.

Reset memory

2.

Transaxle compensation code (Input)

3.

CVT oil pressure calibration


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Replacement of TCM
If transaxle compensation code read from TCM:
1.

Transfer transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


If transaxle compensation code not read from TCM:
1.

Reset transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


Update ECU security key Vehicle control history (RoB) are stored (Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
w/ Stop and Start System:

Bleed air from oil pump (continuously variable transaxle assembly)


Stop and Start System (Click here)
for CVT with Stop and Start System:

Oil pump with motor assembly


Check oil pump with motor assembly
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 11361J 2.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C428831C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101G 3.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C428832

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 4.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 6.DISCONNECT ENGINE WIRE

a.

Disengage the claw, rotate the lever and disconnect the transmission wire connector.

C435470C01
2.583,0.208 2.76,0.375 0.177,0.167 10 true *1 2.885,0.792 3.073,0.958 0.188,0.167 10 true *2 2.896,1.26 3.083,1.417 0.188,0.156 10 true *3 3.729,0.719 3.917,0.875 0.188,0.156 10 true *4 3.073,1.844 3.26,2.021 0.188,0.177 10 true *5 4.375,1.813 4.563,1.979 0.188,0.167 10 true *6 2.635,2.594 2.823,2.76 0.188,0.167 10 true *7 2.167,2.271 2.354,2.427 0.188,0.156 10 true *8
*1 Transmission Wire Connector *2 Shift Stroke Sensor Connector
*3 Park/Neutral Position Switch Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 TCM Connector *6 Transmission Revolution Sensor (NSS) Connector
*7 Oil Pressure Sensor Connector *8 Transmission Revolution Sensor (NT) Connector
V113147

Remove in this Direction - -



b.

Disconnect the shift stroke sensor connector.


c.

Disconnect the park/neutral position switch connector.


d.

Disconnect the transmission revolution sensor (NOUT) connector.


e.

Disengage the claw, rotate the lever and disconnect the TCM connector.


f.

Disconnect the transmission revolution sensor (NSS) connector.


g.

Disconnect the oil pressure sensor connector.


h.

Disconnect the transmission revolution sensor (NT) connector.


i.

Remove the bolt.


j.

Disengage the 4 clamps.


k.
C439374

w/ Stop and Start System:

i.

Disengage the clamp and disconnect the oil pump assembly connector.



l.
C428820

Disconnect the No. 3 water by-pass hose assembly.


m.
C428821

Disengage the 3 clamps.


n.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


o.
C425927

Disengage the 3 clamps to disconnect the engine wire from the front suspension crossmember sub-assembly.


Hide 89535B 7.REMOVE TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to remove the TCM before disconnecting any of the coolant system hoses.


a.
C428824

Remove the 2 bolts and TCM from the continuously variable transaxle assembly.


Hide 16281N 8.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16290F 9.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 28100 10.REMOVE STARTER ASSEMBLY (w/ Stop And Start System)

Hide 28100 11.REMOVE STARTER ASSEMBLY (w/o Stop And Start System)

Hide 12.REMOVE ENGINE ASSEMBLY

a.
C435471N01
0.813,0.26 0.969,0.458 0.156,0.198 10 false C 0.604,0.865 0.76,1.042 0.156,0.177 10 true C 0.833,1.625 0.99,1.802 0.156,0.177 10 true C 2.104,0.052 2.26,0.25 0.156,0.198 10 false A 1.198,1.979 1.354,2.177 0.156,0.198 10 false C 2.521,1.667 2.677,1.865 0.156,0.198 10 false C 2.177,1.99 2.354,2.146 0.177,0.156 10 false B

Remove the 7 bolts and engine assembly from the continuously variable transaxle assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A), (B): Remove from continuously variable transaxle assembly side.

·

Bolt (C): Remove from engine assembly side.




Hide 32000A 13.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C435472

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 14.REMOVE CVT TYPE T OIL SEAL

NOTICE:
·

Do not remove the stator shaft assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C428782E01
1.583,2.667 1.583,2.25 false 1.479,2.677 1.938,2.875 0.458,0.198 10 false SST

Using SST, remove the CVT type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the transaxle housing, as there is the possibility that metal particles could be produced if they do.



Hide 51201 15.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C439375

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 16.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C434365

Remove the 3 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 17.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C428838

Remove the 3 bolts and 3 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 33823 18.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C428826

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 35150B 19.REMOVE TRANSMISSION CASE PLUG ASSEMBLY

a.
C428839C02
0.5,0.083 0.771,0.323 0.271,0.24 12 false *A 1.625,0.083 1.938,0.323 0.313,0.24 12 false *B
*A for Type A
*B for Type B


for Type A:

i.

Remove the transmission case plug assembly from the continuously variable transaxle assembly.


ii.

Remove the O-ring from the transmission case plug assembly.



b.

for Type B:

i.

Remove the transmission case plug assembly from the continuously variable transaxle assembly.



Hide 32000A 20.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 21.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY