Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for HV Model LHD) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432236 BRAKE PEDAL STROKE SENSOR(for HV Model LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for HV Model LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

When installing a new brake pedal stroke sensor assembly:

NOTICE:
C436321C01
0.5,2.042 0.667,2.042 0.667,2.042 0.896,1.938 false 0.333,1.958 0.646,2.156 0.313,0.198 10 false *a
*a Locking Plate


Until the brake pedal stroke sensor assembly has been installed to the brake pedal support assembly with the nut, do not press in the brake pedal stroke sensor lever locking plate.


HINT:

When the brake pedal stroke sensor assembly has been tightened to the specified torque, the locking plate will be released.


i.
C436320C01
1.781,0.656 1.844,0.333 1.844,0.333 1.927,0.333 true 1.938,0.875 2.115,1.135 2.115,1.135 2.208,1.135 true 1.958,0.25 2.146,0.417 0.188,0.167 10 true *a 2.219,1.042 2.406,1.208 0.188,0.167 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove


Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




ii.

Connect the connector.



b.

When reusing the brake pedal stroke sensor assembly:

i.
C436320C01
1.781,0.656 1.844,0.333 1.844,0.333 1.927,0.333 true 1.938,0.875 2.115,1.135 2.115,1.135 2.208,1.135 true 1.958,0.25 2.146,0.417 0.188,0.167 10 true *a 2.219,1.042 2.406,1.208 0.188,0.167 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever
*b Brake Pedal Groove


Install brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




ii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55606 4.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 7. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART