1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
Remove front door scuff plate LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove cowl side trim board LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Turn back tibia pad.
Check the brake pedal height.
Inspect and adjust the brake pedal height with the tibia pad folded back.
Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Height | - | - |
|
Measuring Plane of Floor Panel | - | - |
157.8 to 173.8 mm (6.21 to 6.84 in.)
If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.
| *1 | Stop Light Switch Assembly |
| *2 | Clevis Lock Nut |
| *3 | Floor Panel |
| *a | Brake Pedal Height |
Adjust the brake pedal height.
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the clevis lock nut.
Adjust the brake pedal height by turning the push rod.
157.8 to 173.8 mm (6.21 to 6.84 in.)
Tighten the clevis lock nut.
Install the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Install the tibia pad to its original position.
Install cowl side trim board LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
Install front door scuff plate LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
2.PERFORM INITIALIZATION AND CALIBRATION
3.INSPECT BRAKE PEDAL FREE PLAY
| *a | Brake Pedal Free Play |
Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.
1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the pedal free play is not as specified, check the stop light switch clearance.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.
4.INSPECT BRAKE PEDAL RESERVE DISTANCE
Remove front door scuff plate LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove cowl side trim board LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Turn back tibia pad.
With the ignition switch ON (READY), depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Reserve Distance | - | - |
|
Measuring Plane of Floor Panel | - | - |
82 mm (3.23 in.) or more
If the distance is not as specified, troubleshoot the brake system.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (for HV Model TMMF Made)>PROBLEM SYMPTOMS TABLE
Install the tibia pad to its original position.
Install cowl side trim board LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
Install front door scuff plate LH.
Use the same procedure as for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION