Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422065 TRANSMISSION CONTROL CABLE A

K320 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the TCM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 58166A 8.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 9.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 51447D 10.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

Hide 51447D 11.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 57543C 12.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 17410 13.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58151 14.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
C434360

Remove nut and front No. 1 floor heat insulator from the vehicle body.


Hide 58153 15.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF Made)

a.
C435100

Remove 3 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58153 16.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)

a.
C429238

Remove 4 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58910C 17.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 18.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C435101

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


c.
C435102C01
1.25,2.729 1.542,2.885 true 1.563,2.792 1.771,2.958 0.208,0.167 10 false *1 0.615,2.354 0.802,2.521 0.188,0.167 10 true *a
*1 Lock Nut
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


d.
C429227C03
1.698,2.521 2.031,2.146 false 2.063,2.073 2.375,2.229 0.313,0.156 10 false *1 2.969,3.323 3.281,3.479 0.313,0.156 10 false *a
*1 Clip
*a 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


e.
C429228

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C439382

Remove the nut.


g.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


h.
C439383

Remove the 2 nuts and transmission control cable assembly from the vehicle body.