Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.07–2021.11
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421991 TRANSMISSION CONTROL CABLE A

P910 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Gas leaks from exhaust system Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide G9200 2.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 51451A 3.REMOVE CENTER ENGINE UNDER COVER (w/ Cover)

Hide 58166A 4.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 5.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 51447D 6.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

Hide 51447D 7.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 57543C 8.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58151 10.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
C434360

Remove nut and front No. 1 floor heat insulator from the vehicle body.


Hide 58153 11.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF Made)

a.
C435100

Remove 3 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58153 12.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)

a.
C429503

Remove 4 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58910C 13.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 14.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C435101

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


c.
C435102C01
1.25,2.729 1.542,2.885 true 1.563,2.792 1.771,2.958 0.208,0.167 10 false *1 0.615,2.354 0.802,2.521 0.188,0.167 10 true *a
*1 Lock Nut
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


d.
C429507

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


e.

Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C429508

Disengage the clamp to separate the transmission control cable assembly.


g.

Remove the bolt to disconnect the transmission control cable assembly from the hybrid vehicle transaxle assembly.


h.
C429509

Remove the nut.


i.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


j.
C429510

Remove the 2 nuts and transmission control cable assembly from the vehicle body.