Home › Engine / Hybrid System › M15A-FXE (COOLING) › RADIATOR › from 2020.07
RM36W0E _51 Engine / Hybrid System _088542 M15A-FXE COOLING _0421979 RADIATOR A

M15A-FXE COOLING  RADIATOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B473126

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL

CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 51451A 3.REMOVE CENTER ENGINE UNDER COVER

Hide 4.DRAIN COOLANT (for Inverter)

Hide 5.DRAIN ENGINE COOLANT (for Engine)

Hide 7.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 16681A 8.REMOVE RADIATOR UPPER AIR GUIDE PLATE

Hide 52611 9.REMOVE FRONT BUMPER ENERGY ABSORBER

Hide 52131A 10.REMOVE FRONT BUMPER REINFORCEMENT

Hide 17701 12.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A465284

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the clamp and disconnect the engine wire.


c.

Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose.


d.

Loosen the hose clamp and disconnect the air cleaner hose from the throttle body with motor assembly.


e.

Disengage the 3 grommets to remove the air cleaner case sub-assembly from the vehicle body.


Hide 53213C 13.REMOVE UPPER FRONT RADIATOR SUPPORT

a.

Disconnect the hood lock control cable assembly.

A465285


b.

Disconnect the 2 airbag connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



c.

Disengage the 3 clamps and disconnect the wire harness.


d.

Remove the bolt and disconnect the wire harness.


e.

Disconnect the 2 connectors.


f.

When reusing upper front radiator support:

i.

Place matchmarks as shown in the illustration.

A465286



g.

Remove the 4 bolts and upper front radiator support from the front side member bracket sub-assembly.


Hide 16695A 14.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH

Hide 16691A 15.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH

Hide 16562L 16.REMOVE NO. 2 RADIATOR TO SUPPORT SEAL

Hide 16561D 17.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

a.
A465287

Disengage the claw and guide to remove the No. 1 radiator to support seal.


Hide 16595D 18.REMOVE NO. 1 RADIATOR AIR GUIDE LH

a.
A465288

Disengage the 2 clamps and disconnect the wire harness.


b.

Disengage the claw and guide to remove the No. 1 radiator air guide LH.


Hide 16261G 19.DISCONNECT NO. 1 WATER BY-PASS HOSE

a.
A465289

Disengage the 3 clamps.


b.

Slide the clip and disconnect the No. 1 water by-pass hose from the radiator assembly.


Hide 20.DISCONNECT RADIATOR RESERVOIR TANK HOSE

a.
A465290

Disconnect the radiator reservoir tank hose from the water filler sub-assembly.


Hide 16502 21.SEPARATE WATER FILLER SUB-ASSEMBLY

a.
A465291

Disconnect the connector.


b.

Disengage the 3 clamps.


c.

Remove the 2 bolts to separate the water filler sub-assembly from the fan shroud.


Hide 16573B 22.DISCONNECT NO. 3 RADIATOR HOSE

a.
A465292

Slide the clip and disconnect the No. 3 radiator hose from the radiator assembly.


Hide G922C 23.DISCONNECT NO. 1 INVERTER COOLING OUTLET HOSE

a.
A465293

Disengage the 2 clamps and disconnect the No. 1 inverter cooling outlet hose from the fan shroud.


Hide G9040 24.REMOVE INVERTER WATER PUMP ASSEMBLY

Hide G922H 25.DISCONNECT HYBRID RADIATOR INLET HOSE

a.
A465294

Disengage the clamp.


b.

Slide the clip and disconnect the hybrid radiator inlet hose from the radiator assembly.


Hide G922F 26.DISCONNECT NO. 1 HYBRID WATER PUMP OUTLET HOSE

a.
A465295

Disengage the clamp and disconnect the No. 1 hybrid water pump outlet hose from the fan shroud.


Hide G922E 27.DISCONNECT HYBRID WATER PUMP INLET HOSE

a.
A465296

Disengage the 2 clamps and disconnect the hybrid water pump inlet hose from the fan shroud.


Hide G922AA 28.DISCONNECT NO. 1 INVERTER COOLING INLET HOSE

a.
A465297

Disengage the clamp.


b.

Slide the clip and disconnect the No. 1 inverter cooling inlet hose from the radiator assembly.


Hide 16572D 29.DISCONNECT NO. 2 RADIATOR HOSE

a.
A465298

Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.


Hide 88460 30.SEPARATE COOLER CONDENSER ASSEMBLY

a.
A465299

Disengage the 2 claws and 2 guides to separate the cooler condenser assembly from the radiator assembly.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when separating the cooler condenser assembly.



Hide 16400 31.REMOVE RADIATOR ASSEMBLY

a.
A465300

Disengage the clamp and disconnect the wire harness.


b.

Remove the radiator assembly together with the fan shroud from the vehicle body.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan shroud.



c.
A465301

Disengage the 2 claws and 2 guides to remove the fan shroud from the radiator assembly.

NOTICE:

Do not damage the radiator assembly when removing the fan shroud.



Hide 16523A 32.REMOVE RADIATOR SUPPORT CUSHION

a.
A465302

Remove the 2 radiator support cushions from the radiator assembly.


Hide 16535 33.REMOVE LOWER RADIATOR SUPPORT

a.
A465303

Remove the 2 lower radiator supports from the radiator assembly.


Hide 34.REMOVE RADIATOR DRAIN COCK PLUG

a.
A465304

Remove the 2 radiator drain cock plugs.


b.

Remove the 2 O-rings from the radiator drain cock plugs.