The combination meter assembly receives vehicle speed signals from the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2. The skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 supplies power to the vehicle speed sensor. The skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 detects vehicle speed signals based on pulses of the voltage.
*1: for TMC Made HV Model
*2: except TMC Made HV Model
Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before starting the following inspection, inspect the speedometer and check that the tire size and air pressure are as specified.
Tire size and air pressure: Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Speedometer: Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
Check if CAN communication DTCs are output.
for HV Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
for Gasoline Model:
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING
Check if electronically controlled brake system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
for HV Model TMC Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>DIAGNOSTIC TROUBLE CODE CHART
for HV Model TMMF Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>DIAGNOSTIC TROUBLE CODE CHART
for Gasoline Model TMC Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>DIAGNOSTIC TROUBLE CODE CHART
for Gasoline Model TMMF Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>DIAGNOSTIC TROUBLE CODE CHART
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speedometer Operation (0km/h,0MPH) | Speedometer
(0 km/h, 0 mph) |
ON | When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. |
| Speedometer Operation (40km/h,40MPH) | Speedometer
(40 km/h, 40 mph) |
ON | ·
When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. ·
The value displayed on the speedometer may deviate.*1 |
| Speedometer Operation (80km/h,80MPH) | Speedometer
(80 km/h, 80 mph) |
ON | ·
When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. ·
The value displayed on the speedometer may deviate.*1 |
| Speedometer Operation (120km/h,120MPH) | Speedometer
(120 km/h, 120 mph) |
ON | ·
When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. ·
The value displayed on the speedometer may deviate.*1 |
| Speedometer Operation (160km/h,160MPH) | Speedometer
(160 km/h, 160 mph) |
ON | ·
When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. ·
The value displayed on the speedometer may deviate.*1 |
| Speedometer Operation (200km/h,200MPH) | Speedometer
(200 km/h, 200 mph) |
ON | ·
When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. ·
The value displayed on the speedometer may deviate.*1 |
| Speedometer Operation (240km/h,240MPH) | Speedometer
(240 km/h, 240 mph) |
ON | When this Active Test is performed, an operation signal is sent directly to the combination meter assembly to operate the speedometer. |
*1: For the tolerance of each Speed Signal Input Active Test, refer to On-vehicle Inspection.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
| Tester Display |
|---|
| Speedometer Operation (0km/h,0MPH) |
| Tester Display |
|---|
| Speedometer Operation (40km/h,40MPH) |
| Tester Display |
|---|
| Speedometer Operation (80km/h,80MPH) |
| Tester Display |
|---|
| Speedometer Operation (120km/h,120MPH) |
| Tester Display |
|---|
| Speedometer Operation (160km/h,160MPH) |
| Tester Display |
|---|
| Speedometer Operation (200km/h,200MPH) |
| Tester Display |
|---|
| Speedometer Operation (240km/h,240MPH) |
Speedometer indication is normal.
When the value of the Active Test is more than or equal to the speedometer upper limit, the indicated speed stops at the upper limit.
| Result | Proceed to |
|---|---|
| OK (for TMC Made HV Model) | A |
| OK (except TMC Made HV Model) | B |
| NG | C |
A
B
for HV Model RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
for HV Model LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for Gasoline Model TMC Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for Gasoline Model TMMF Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
for Gasoline Model LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
C