Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0420504 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects whether either the rear seat occupied or unoccupied based on the rear occupant detection sensor condition and then sends the rear occupant detection sensor status signal to the combination meter assembly.

The power distribution box assembly detects whether either the rear seat belts are fastened or unfastened based on the rear seat belt buckle switch condition and then sends the rear seat belt buckle switch status signal to the combination meter assembly.

The combination meter assembly illuminates, blinks or turns off the rear seat belt warning light on the combination meter assembly in accordance with the vehicle speed, rear seat belt state and rear seat occupant state.

WIRING DIAGRAM

E437939E04
5.51,7.688 6.938,8.073 1.427,0.385 10 false Power Distribution Box Assembly 6.5,4.344 6.823,4.708 0.323,0.365 10 false IC 5.729,1.198 6.938,1.76 1.208,0.563 10 false Combination Meter Assembly 3.427,4.031 5.094,4.49 1.667,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 0.906,4.542 2.385,5.229 1.479,0.688 10 false Rear Seat Cushion Pad Sub-assembly 0.885,1.042 2.458,1.698 1.573,0.656 10 false O61 0.854,2.479 2.427,3.135 1.573,0.656 10 false Rear Occupant Detection Sensor (for Center) 0.854,3.74 2.427,4.396 1.573,0.656 10 false Rear Occupant Detection Sensor (for RH) 3.146,3.354 3.469,3.719 0.323,0.365 10 false H4 3.135,2.115 3.458,2.479 0.323,0.365 10 false H4 3.135,0.823 3.458,1.188 0.323,0.365 10 false H4 0.531,7.917 2.76,8.406 2.229,0.49 10 false : CAN Communication Line 0.531,8.375 2.771,8.792 2.24,0.417 10 false : CXPI Communication Line 3.094,5.604 3.417,5.969 0.323,0.365 10 false O19 2.896,7.708 4.625,8.323 1.729,0.615 10 false Rear Seat Inner with Center Belt Assembly LH 2.896,7.531 3.219,7.896 0.323,0.365 10 false O20 5.115,5.313 5.438,5.677 0.323,0.365 10 false 4E 5.115,6.594 5.438,6.958 0.323,0.365 10 false 4E 5.146,6.375 5.469,6.74 0.323,0.365 10 false 4 5.146,5.125 5.469,5.49 0.323,0.365 10 false 8 5.115,2.385 5.438,2.75 0.323,0.365 10 false MB 5.135,2.188 5.458,2.552 0.323,0.365 10 false 22 4.635,2.396 5.219,2.802 0.583,0.406 10 false CXPI 3.146,3.156 3.469,3.521 0.323,0.365 10 false 25 3.146,1.906 3.469,2.271 0.323,0.365 10 false 23 3.146,0.625 3.469,0.99 0.323,0.365 10 false 24 3.458,0.823 4.042,1.229 0.583,0.406 10 false RLSS 3.458,3.375 4.042,3.781 0.583,0.406 10 false RRSS 3.458,2.115 4.042,2.521 0.583,0.406 10 false RCSS 4.438,7.042 4.76,7.406 0.323,0.365 10 false 5 2.313,0.719 2.635,1.083 0.323,0.365 10 false 2 2.323,2 2.646,2.365 0.323,0.365 10 false 2 2.313,3.24 2.635,3.604 0.323,0.365 10 false 2 0.854,0.708 1.177,1.073 0.323,0.365 10 false 1 0.875,2 1.198,2.365 0.323,0.365 10 false 1 0.844,3.24 1.167,3.604 0.323,0.365 10 false 1 1.042,3.25 1.365,3.615 0.323,0.365 10 false E 1.042,2 1.365,2.365 0.323,0.365 10 false E 1.042,0.708 1.365,1.073 0.323,0.365 10 false E 2.115,0.708 2.438,1.073 0.323,0.365 10 false + 2.135,1.99 2.458,2.354 0.323,0.365 10 false + 2.125,3.24 2.448,3.604 0.323,0.365 10 false + 0.885,1.229 2.458,1.885 1.573,0.656 10 false Rear Occupant Detection Sensor (for LH) 0.854,2.323 2.427,2.979 1.573,0.656 10 false O63 0.854,3.573 1.917,3.917 1.063,0.344 10 false O62 4.438,6.49 4.76,6.854 0.323,0.365 10 false 3 5.125,7.146 5.448,7.51 0.323,0.365 10 false 4E 5.125,6.958 5.448,7.323 0.323,0.365 10 false 19 4.438,5.188 4.76,5.552 0.323,0.365 10 false 5 2.917,5.188 3.24,5.552 0.323,0.365 10 false 4 2.927,7.042 3.25,7.406 0.323,0.365 10 false 4 2.917,6.479 3.24,6.844 0.323,0.365 10 false 2 3.094,5.781 4.823,6.396 1.729,0.615 10 false Rear Seat Inner Belt Assembly RH 3.938,5.188 4.521,5.5 0.583,0.313 10 false RBR+ 3.104,5.177 3.688,5.49 0.583,0.313 10 false RBR- 3.115,6.479 3.698,6.792 0.583,0.313 10 false CBR- 3.125,7.031 3.708,7.344 0.583,0.313 10 false LBR- 3.948,6.479 4.531,6.792 0.583,0.313 10 false CBR+ 3.958,7.042 4.542,7.354 0.583,0.313 10 false LBR+

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system and CXPI communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (REAR SEAT RH BUCKLE SWITCH STATUS / REAR SEAT CENTER BUCKLE SWITCH STATUS / REAR SEAT LH BUCKLE SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Seat RH Buckle Switch Status Rear RH seat belt buckle switch status Set/Unset/Unknown Set: Rear RH seat belt fastened
Unset: Rear RH seat belt not fastened
-
Rear Seat Center Buckle Switch Status Rear center seat belt buckle switch status Set/Unset/Unknown Set: Rear center seat belt fastened
Unset: Rear center seat belt not fastened
-
Rear Seat LH Buckle Switch Status Rear LH seat belt buckle switch status Set/Unset/Unknown Set: Rear LH seat belt fastened
Unset: Rear LH seat belt not fastened
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Rear Seat RH Buckle Switch Status
Rear Seat Center Buckle Switch Status
Rear Seat LH Buckle Switch Status
50003 475 1402,1403,1404
OK:

The GTS display changes correctly in response to the rear seat belt buckle switch condition.



Result:
Result Proceed to
OK A
NG (Rear RH seat belt malfunction) B
NG (Rear center or rear LH seat belt malfunction) C



A

2.READ VALUE USING GTS (REAR SEAT RH BUCKLE SWITCH STATUS / REAR SEAT CENTER BUCKLE SWITCH STATUS / REAR SEAT LH BUCKLE SWITCH STATUS)

B

5.INSPECT REAR SEAT INNER BELT ASSEMBLY RH

C

7.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
2.READ VALUE USING GTS (REAR SEAT RH BUCKLE SWITCH STATUS / REAR SEAT CENTER BUCKLE SWITCH STATUS / REAR SEAT LH BUCKLE SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RC-Seat Occupant Sensor Switch Rear occupant detection sensor (for center) ON or OFF ON: Rear center seat occupied
OFF: Rear center seat not occupied
-
RL-Seat Occupant Sensor Switch Rear occupant detection sensor (for LH) ON or OFF ON: Rear LH seat occupied
OFF: Rear LH seat not occupied
-
RR-Seat Occupant Sensor Switch Rear occupant detection sensor (for RH) ON or OFF ON: Rear RH seat occupied
OFF: Rear RH seat not occupied
-
Body Electrical > Main Body > Data List
Tester Display
RC-Seat Occupant Sensor Switch
RL-Seat Occupant Sensor Switch
RR-Seat Occupant Sensor Switch
50003 449 131,132,133
OK:

The GTS display changes correctly in response to the rear seat condition (occupied or unoccupied).



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.INSPECT REAR OCCUPANT DETECTION SENSOR
3.INSPECT REAR OCCUPANT DETECTION SENSOR

OK

4.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)

NG

REPLACE REAR OCCUPANT DETECTION SENSOR (REAR SEAT CUSHION PAD SUB-ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (REAR OCCUPANT DETECTION SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) OR BODY GROUND)
a.

Disconnect the O61 rear occupant detection sensor (for LH) connector.


b.

Disconnect the O62 rear occupant detection sensor (for RH) connector.


c.

Disconnect the O63 rear occupant detection sensor (for center) connector.


d.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
O61-2 (+) - H4-24 (RLSS) Always Below 1 Ω
O61-2 (+) or H4-24 (RLSS) - Body ground Always 10 kΩ or higher
O61-1 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
O62-2 (+) - H4-25 (RRSS) Always Below 1 Ω
O62-2 (+) or H4-25 (RRSS) - Body ground Always 10 kΩ or higher
O62-1 (E) - Body ground Always Below 1 Ω

for Center
Tester Connection Condition Specified Condition
O63-2 (+) - H4-23 (RCSS) Always Below 1 Ω
O63-2 (+) or H4-23 (RCSS) - Body ground Always 10 kΩ or higher
O63-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR SEAT INNER BELT ASSEMBLY RH

OK

6.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - POWER DISTRIBUTION BOX AND BODY GROUND)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - POWER DISTRIBUTION BOX AND BODY GROUND)
a.

Disconnect the O19 rear seat inner belt assembly RH connector.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O19-5 (RBR+) - 4E-8 Always Below 1 Ω
O19-5 (RBR+) or 4E-8 - Body ground Always 10 kΩ or higher
O19-4 (RBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

OK

8.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - POWER DISTRIBUTION BOX AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - POWER DISTRIBUTION BOX AND BODY GROUND)
a.

Disconnect the O20 rear seat inner with center belt assembly LH connector.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O20-3 (CBR+) - 4E-4 Always Below 1 Ω
O20-3 (CBR+) or 4E-4 - Body ground Always 10 kΩ or higher
O20-5 (LBR+) - 4E-19 Always Below 1 Ω
O20-5 (LBR+) or 4E-19 - Body ground Always 10 kΩ or higher
O20-2 (CBR-) - Body ground Always Below 1 Ω
O20-4 (LBR-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR