Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM C

G16E-GTS ENGINE CONTROL  SFI SYSTEM  P001600  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  P001700  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve) and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P001600 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Deviation in the crankshaft position sensor signal and camshaft sensor (for intake camshaft) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for intake camshaft)

·

Camshaft timing gear bolt (intake camshaft timing oil control valve)

·

Camshaft timing gear assembly

·

ECM


Comes on SAE: P0016
P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly (for exhaust camshaft)

·

Camshaft timing gear bolt (exhaust camshaft timing oil control valve)

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on SAE: P0017

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the neutral position while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001600.

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001700.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A197314E71
4.271,1.115 4.604,0.448 4.604,0.448 4.75,0.448 false 0.156,0.656 1.083,0.802 0.927,0.146 10 false Vehicle Speed 1.542,2.156 1.75,2.354 0.208,0.198 10 false [A] 2.167,1.656 2.396,1.823 0.229,0.167 10 false [B] 3.188,1.646 3.396,1.802 0.208,0.156 10 false [C] 3.823,3.01 4.031,3.167 0.208,0.156 10 false [D] 4.625,0.865 4.823,1.063 0.198,0.198 10 false [E] 5.656,1.615 5.854,1.813 0.198,0.198 10 false [F] 6.375,3.021 6.615,3.208 0.24,0.188 10 false [G] 0.667,1.792 1.052,1.979 0.385,0.188 10 false Idling 4.813,0.365 6.292,0.729 1.479,0.365 10 false There is no designated vehicle speed 0.167,2.083 1.073,2.51 0.906,0.427 10 false Ignition Switch ON 1.917,2.573 2.708,2.906 0.792,0.333 10 false Warming up the engine 2.74,2.583 3.896,2.75 1.156,0.167 10 false 5 minutes or more 5.271,2.604 6.427,2.771 1.156,0.167 10 false 5 minutes or more 4.125,2.604 5.021,2.771 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Idle the engine for 5 minutes or more [C].

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P001600 or P001700.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [E] through [G].



15.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Idle the engine for 5 minutes or more [F].

17.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

18.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



19.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by two teeth or more.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001700)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P001600 or P001700 and other DTCs are output A
P001600 or P001700 is output B


HINT:

If any DTCs other than P001600 or P001700 is output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1 OR CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1 OR CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


Pre-procedure1

a.

Start the engine.


Procedure1

b.

Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Intake VVT OCV Control Duty Ratio Bank 1
50004 372 4 397,296
OK:

Displacement angle varies.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

HINT:

Click hereEngine / Hybrid System>G16E-GTS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

5.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

6.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

6.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

OK

7.INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)

NG

REPLACE CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

7.INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)

OK

8.CLEAR DTC

NG

REPLACE CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)

8.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

d.

None.


Result:
Result Proceed to
DTCs are not output A
P001600 or P001700 is output B



A

B

10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
HINT:

Click hereEngine / Hybrid System>G16E-GTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

d.

None.


Result:
Result Proceed to
DTCs are not output A
P001600 or P001700 is output B



A

B