This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
19100P
1.REMOVE SPARK PLUG
89448D
2.REMOVE OIL PRESSURE AND TEMPERATURE SENSOR
11102A
3.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)
11102A
4.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)
15370
5.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)
15370
6.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)
16031
7.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
16032
8.INSTALL WATER INLET WITH WATER PUMP HOUSING SUB-ASSEMBLY
12180E
9.REMOVE OIL FILLER CAP ASSEMBLY
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.
12108A
10.REMOVE OIL FILLER CAP GASKET
Remove the oil filler cap gasket from the oil filler cap sub-assembly.
11401G
11.REMOVE CRANKSHAFT POSITION SENSOR
12204C
12.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
29300
13.REMOVE VACUUM PUMP ASSEMBLY
13471
14.REMOVE CRANKSHAFT PULLEY ASSEMBLY
| *a | Hold |
| *b | Turn |
Using SST, hold the crankshaft pulley assembly and loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads remain screwed into the crankshaft.
| *1 | Crankshaft Pulley Set Bolt |
| *a | Hold |
| *b | Turn |
Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley assembly and crankshaft pulley set bolt.
Apply lubricant to the threads and end of SST.
16304
15.REMOVE OUTLET WATER SUB-ASSEMBLY
Remove the 2 nuts, outlet water sub-aseembly and water outlet gasket from the cylinder head sub-assembly.
11201
16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 17 bolts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
Remove the 5 cylinder head cover gaskets from the cylinder head cover sub-assembly.
Remove the 2 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap and fuel pump lifter housing.
11193
17.REMOVE SPARK PLUG TUBE GASKET
| *a | Protective Tape |
Using a screwdriver, pry out the 3 spark plug tube gaskets from the cylinder head cover sub-assembly.
Be careful not to damage the cylinder head cover sub-assembly.
Tape the screwdriver tip before use.
12551A
18.REMOVE NO. 1 VACUUM PUMP BRACKET
Remove the 4 bolts and No. 1 vacuum pump bracket from the cylinder head sub-assembly.
12315A
19.REMOVE ENGINE MOUNTING BRACKET RH
Remove the 3 bolts and engine mounting bracket RH from the No. 2 timing chain cover assembly.
11310
20.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY
Remove the 8 bolts.
Remove the No. 2 timing chain cover assembly from the cylinder head sub-assembly by prying the No. 2 timing chain cover assembly with a screwdriver with its tip wrapped with protective tape.
11301C
21.REMOVE TIMING CHAIN COVER OIL SEAL
11310
22.REMOVE TIMING CHAIN COVER ASSEMBLY
23.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Temporarily install the crankshaft pulley bolt.
| *a | Timing Mark |
Rotate the crankshaft clockwise and make sure that the timing mark of the camshaft timing gear assembly and camshaft timing exhaust gear assembly is at the top.
| *1 | Crankshaft Timing Gear Key |
| *a | Approximately 27° |
Check that the crankshaft timing gear key as shown in the illustration.
Remove the crankshaft pulley bolt.
As the exhaust camshaft sub-assembly may rotate counterclockwise strongly when the crankshaft pulley bolt is removed, use a wrench to hold the hexagonal portion of the exhaust camshaft sub-assembly.
13540
24.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *1 | Stopper Plate |
| *2 | plunger |
Turn the stopper plate of the No. 1 chain tensioner assembly clockwise to release the lock and push in the plunger.
Turn the stopper plate counterclockwise to set the lock.
Turn the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder block sub-assembly.
Remove the chain tensioner gasket from the No. 1 chain tensioner assembly.
13566B
25.REMOVE TIMING CHAIN GUIDE
Remove the 2 nut and timing chain guide from the damper plate spacer.
87156N
26.REMOVE DAMPER PLATE SPACER
Remove the damper plate spacer from the No. 1 camshaft bearing cap.
13559
27.REMOVE CHAIN TENSIONER SLIPPER
Remove the bolt and chain tensioner slipper from the cylinder head sub-assembly.
13506
28.REMOVE CHAIN SUB-ASSEMBLY
Remove the chain sub-assembly.
13561
29.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper from the timing chain cover assembly.
13521
30.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET
Remvoe the crankshaft timing gear or sprocket from the crankshaft.
13471A
31.REMOVE CRANKSHAFT TIMING GEAR KEY
| *a | Protective Tape |
Using a screwdriver, remove the 2 crankshaft timing gear keys from the crankshaft.
Tape the screwdriver tip before use.
13070A
32.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.
Using a 5 mm hexagon socket wrench, remove the 3 bolts.
| *1 | Camshaft Timing Exhaust Gear Assembly |
| *2 | Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly) |
Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) from the exhaust camshaft sub-assembly.
13050
33.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.
Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
Using a 5 mm hexagon socket wrench, remove the 3 bolts.
| *1 | Camshaft Timing Gear Assembly |
| *2 | Camshaft Timing Oil Control Valve Assembly (Camshaft Timing Gear Bolt Assembly) |
Remove the camshaft timing gear assembly and camshaft timing oil control valve assembly (camshaft timing gear bolt assembly) from the intake camshaft sub-assembly.
23477
34.REMOVE FUEL PUMP LIFTER GUIDE
Remove the 2 bolts and fuel pump lifter guide from the fuel pump lifter housing.
23476
35.REMOVE FUEL PUMP LIFTER HOUSING
Remove the 3 bolts and fuel pump lifter housing from the cylinder head sub-aseembly.
19318
36.REMOVE CAMSHAFT POSITION SENSOR HOLDER
Remove the bolt and camshaft position sensor holder from the cylinder head sub-assembly.
37.REMOVE CAMSHAFT BEARING CAP
| *1 | No. 2 Camshaft Bearing Cap |
| *2 | No. 4 Camshaft Bearing Cap |
Remove the 16 bolts.
Remove the No. 2 camshaft bearing cap, 6 No. 4 camshaft bearing caps from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13502B
38.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY
Remove the exhaust camshaft sub-assembly from the camshaft housing sub-assembly.
13501A
39.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY
Remove the intake camshaft sub-assembly from the camshaft housing sub-assembly.
40.REMOVE NO. 1 CAMSHAFT BEARING CAP
Remove the No. 1 camshaft bearing cap from the cylinder head sub-assembly.
13801
41.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 12 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13750
42.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 12 valve lash adjuster assemblies from the cylinder head sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13716
43.REMOVE VALVE STEM CAP
Remove the 12 valve stem caps from the cylinder head sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
11101
44.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 12 mm socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 plate washers.
Be careful not to drop the plate washers into the cylinder head sub-assembly.
Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
Remove the 3 bolts and cylinder head sub-assembly from the cylinder block sub-assembly.
11115
45.REMOVE CYLINDER HEAD GASKET
15601
46.REMOVE OIL FILTER SUB-ASSEMBLY
15600A
47.REMOVE OIL FILTER UNION
Using a 12 mm hexagon socket wrench, remove the oil filter union from the stiffening crankcase assembly.
15710
48.REMOVE OIL COOLER ASSEMBLY
15609
49.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
Remvoe the 3 bolts and oil filter bracket sub-assembly from the cylinder block sub-aseembly.
Remove the 2 gaskets.
12101A
50.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket from the No. 2 oil pan sub-assembly.
12102A
51.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
| *a | Nut |
Remove the 10 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.
Be careful not to damage the oil pan sub-assembly flange.
12101D
52.REMOVE NO. 1 OIL PAN PLUG
Using a 10 mm hexagon socket wrench, remove the 2 No. 1 oil pan plugs and 2 gaskets from the oil pan sub-assembly.
12101
53.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 13 bolts and oil pan sub-aseembly from the crankshaft bearing cap assembly.
15104
54.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 bolts, oil strainer sub-assembly and oil strainer gasket from the cylinder block sub-assembly.
13620B
55.REMOVE ENGINE BALANCER ASSEMBLY
Remove the 4 bolts and engine balancer assembly from the cylinder block sub-assembly.
11485A
56.REMOVE BALANCESHAFT HOUSING SPACER
Remove the balanceshaft housing spacer from the cylinder block sub-assembly.
11401L
57.REMOVE REAR ENGINE OIL SEAL
58.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
59.REMOVE RING PIN
It is not necessary to remove the ring pins unless they are being replaced.