Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › CAMSHAFT › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447809 CAMSHAFT A

G16E-GTS ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Engine coolant temperature sensor

·

Spark plug


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 11336A 1.REMOVE TIMING GEAR COVER INSULATOR

Hide 19100P 2.REMOVE SPARK PLUG

Hide 89448D 3.REMOVE OIL PRESSURE AND TEMPERATURE SENSOR

Hide 11102A 4.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 6.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 15370 7.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

Hide 16031 8.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16032 9.REMOVE WATER INLET WITH WATER PUMP HOUSING SUB-ASSEMBLY

Hide 12180E 10.REMOVE OIL FILLER CAP ASSEMBLY

Hide 11401G 11.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204C 12.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 29300 13.REMOVE VACUUM PUMP ASSEMBLY

Hide 13471 14.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 16.REMOVE SPARK PLUG TUBE GASKET

Hide 12551A 17.REMOVE NO. 1 VACUUM PUMP BRACKET

Hide 12315A 18.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11304 19.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 20.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 11310 21.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 22. NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 23.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 26.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 28.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 29.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

Hide 13070A 30.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 31.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 23477 32.REMOVE FUEL PUMP LIFTER GUIDE

Hide 23476 33.REMOVE FUEL PUMP LIFTER HOUSING

Hide 19318 34.REMOVE CAMSHAFT POSITION SENSOR HOLDER

Hide 11159H 35.REMOVE CAMSHAFT BEARING CAP OIL HOLE GASKET

Hide 13502B 36.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 13501A 37.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY