89348N
1.REMOVE NO. 1 ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)
89341K
2.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89341L
3.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)
89347B
4.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)
88211B
5.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense 2)
82113
6.REMOVE NO. 3 ENGINE ROOM WIRE (w/ Wire Harness)
w/ Parking Support Brake System:
Disengage the clamps to remove the No. 3 engine room wire.
w/o Parking Support Brake System:
Disengage the clamps to remove the No. 3 engine room wire.
81220
7.REMOVE FOG LIGHT ASSEMBLY LH
81210A
8.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
81482C
9.REMOVE FOG LIGHT COVER LH
Remove the 2 screws.
Disengage the claws and guide to remove the fog light cover LH.
81481E
10.REMOVE FOG LIGHT COVER RH
Use the same procedure as for the LH side.
52127C
11.REMOVE FRONT BUMPER HOLE COVER
Disengage the claws.
Disengage the hook to remove the front bumper hole cover.
53395E
12.REMOVE HOOD TO FRONT END PANEL SEAL
Disengage the clips to remove the hood to front end panel seal.
52114B
13.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET
Remove the 2 screws.
Disengage the claws and guides to remove the front bumper extension mounting bracket.
53102B
14.REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY
Remove the 3 screws and 4 clips.
Disengage the claws to remove the lower radiator grille sub-assembly.
53124F
15.REMOVE RADIATOR GRILLE SIDE MOULDING LH
Remove the screw.
Disengage the claws to remove the radiator grille side moulding LH.
53123G
16.REMOVE RADIATOR GRILLE SIDE MOULDING RH
Use the same procedure as for the LH side.
75310A
17.REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY
Remove the screw.
Disengage the claws to remove the radiator grille emblem assembly.
18.REMOVE HEADLIGHT ASSEMBLY LH
19.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52536
20.REMOVE FRONT BUMPER SIDE RETAINER LH
Disengage the clip and claw to remove the front bumper side retainer LH as shown in the illustration.
52535
21.REMOVE FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
16681A
22.REMOVE RADIATOR UPPER AIR GUIDE PLATE
Remove the 2 clips and radiator upper air guide plate.
52611
23.REMOVE FRONT BUMPER ENERGY ABSORBER
Disengage the guides to remove the front bumper energy absorber.
88790B
24.SEPARATE THERMISTOR ASSEMBLY
Disengage the clamps to separate the thermistor assembly.
53288A
25.REMOVE COOL AIR INTAKE DUCT
Remove the 3 clips and cool air intake duct.
52131A
26.REMOVE FRONT BUMPER REINFORCEMENT
Disengage the wire harness clamp.
Remove the 8 bolts.
Disengage the guides to remove the front bumper reinforcement.
16695A
27.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH
|
Remove in this Direction |
Disengage the claws to remove the front radiator side air guide plate LH as shown in the illustration.
16691A
28.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH
|
Remove in this Direction |
Disengage the claws to remove the front radiator side air guide plate RH as shown in the illustration.
16595D
29.REMOVE NO. 1 RADIATOR AIR GUIDE LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw and guide to remove the No. 1 radiator air guide LH as shown in the illustration.
16593B
30.REMOVE NO. 1 RADIATOR AIR GUIDE RH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claw and guide to remove the No. 1 radiator air guide RH as shown in the illustration.
57014C
31.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
If reusing the front side member bracket sub-assembly LH:
Put matchmarks on the front side member bracket sub-assembly LH as shown in the illustration.
Disengage the clamp.
Remove the 5 bolts and front side member bracket sub-assembly LH.
57013D
32.REMOVE FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
If reusing the front side member bracket sub-assembly RH:
Put matchmarks on the front side member bracket sub-assembly RH as shown in the illustration.
Remove the 5 bolts and front side member bracket sub-assembly RH.
51410
33.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
52618
34.REMOVE FRONT BUMPER LOWER ABSORBER
| *a | screw |
| *b | clip |
Remove the clip and 5 screws.
Disengage the claws to remove the front bumper lower absorber.
Remove the 4 grommets.