Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.09
RM36W0E _58 Vehicle Interior _087985 METER / GAUGE / DISPLAY _0420292 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150013  Fuel Sender Circuit Open  B150113  Sub Fuel Sender Circuit Open  


DESCRIPTION

·

The fuel sender gauge assembly is connected to the combination meter assembly via direct line. If there is an open or short in the direct line, the combination meter assembly stores DTC B150013.

·

The fuel sender gauge assembly and No. 2 fuel sender gauge assembly are connected to the combination meter assembly via direct line. If there is an open or short in the direct line, the combination meter assembly stores DTC B150013 or B150113. *1

*1: for Gasoline Model AWD



DTC No. Detection Item DTC Detection Condition Trouble Area
B150013 Fuel Sender Circuit Open Diagnosis Condition:
·

The ignition switch is ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more


Malfunction Time:

10 seconds or more


·

Harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter assembly


B150113 Sub Fuel Sender Circuit Open Diagnosis Condition:
·

The ignition switch is ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from No. 2 fuel sender gauge assembly is 0.2 V or less

·

Voltage signal from No. 2 fuel sender gauge assembly is 4.7 V or more


Malfunction Time:

10 seconds or more


·

Harness or connector

·

No. 2 fuel sender gauge assembly

·

Fuel tank vent tube assembly

·

Combination meter assembly



WIRING DIAGRAM

E436631E03
1.979,0.635 2.292,0.833 0.313,0.198 10 false FS 1.969,1.042 2.281,1.24 0.313,0.198 10 false FV 1.979,1.469 2.292,1.667 0.313,0.198 10 false FE 0.885,0.885 1.042,1.083 0.156,0.198 10 false 1 2.271,1.042 2.427,1.24 0.156,0.198 10 false 1 2.271,0.635 2.427,0.833 0.156,0.198 10 false 3 1.521,1.031 1.677,1.229 0.156,0.198 10 false 3 1.521,1.458 1.677,1.656 0.156,0.198 10 false 2 2.271,1.469 2.427,1.667 0.156,0.198 10 false 2 0.302,1.844 0.458,2.042 0.156,0.198 10 false A 0.292,2.01 2.354,2.396 2.063,0.385 10 false Fuel Sender Gauge Assembly 0.125,2.771 2.229,3.167 2.104,0.396 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.125,2.615 0.646,2.844 0.521,0.229 10 false O22 6.167,0.458 6.563,0.729 0.396,0.271 10 false 5 V 4.917,0.625 5.229,0.823 0.313,0.198 10 false FR 4.917,1.042 5.479,1.302 0.563,0.26 10 false FV 4.906,1.448 5.469,1.708 0.563,0.26 10 false FE&B 4.906,3.531 5.219,3.729 0.313,0.198 10 false FR2 4.656,3.531 4.969,3.729 0.313,0.198 10 false 13 4.677,0.625 4.99,0.823 0.313,0.198 10 false 31 4.656,1.042 4.969,1.24 0.313,0.198 10 false 14 4.667,1.458 4.979,1.656 0.313,0.198 10 false 24 0.26,5.75 3.167,5.948 2.906,0.198 10 false Fuel Tank Vent Tube Assembly 0.25,5.573 0.708,5.771 0.458,0.198 10 false O23 0.427,4.927 1.615,5.375 1.188,0.448 10 false No. 2 Fuel Sender Gauge Assembly 0.427,4.771 0.583,4.969 0.156,0.198 10 false B 0.875,3.844 1.031,4.042 0.156,0.198 10 false 1 2.271,3.99 2.427,4.188 0.156,0.198 10 false 1 2.281,4.406 2.438,4.604 0.156,0.198 10 false 2 1.542,4.406 1.698,4.604 0.156,0.198 10 false 2 1.531,3.99 1.688,4.188 0.156,0.198 10 false 3 2.271,3.573 2.427,3.771 0.156,0.198 10 false 3 1.99,4.417 2.302,4.615 0.313,0.198 10 false FE 1.969,3.99 2.281,4.188 0.313,0.198 10 false FV 1.969,3.573 2.281,3.771 0.313,0.198 10 false FR 4.927,4.552 5.24,4.75 0.313,0.198 10 false H6 4.917,4.719 6.927,5.156 2.01,0.438 10 false Combination Meter Assembly 3.104,2.729 3.417,2.927 0.313,0.198 10 false *1 4.083,3.573 4.396,3.771 0.313,0.198 10 false *1 3.573,2.729 3.885,2.927 0.313,0.198 10 false *1 0.167,6.417 2.083,6.75 1.917,0.333 10 false *1: for Gasoline Model AWD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150013 is output A
B150113 is output B
B150013 and B150113 are output C



A

2.READ VALUE USING GTS

B

6.READ VALUE USING GTS

C

10.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0.00 L, Max.: 655.35 L or Unset Fuel sender input value -
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 409 20

Result:
Result Proceed to
Fuel level data can be displayed on the GTS. A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

3.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the O22 fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the H6 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O22-1 (FV) - H6-14 (FV) Always Below 1 Ω
O22-3 (FS) - H6-31 (FR) Always Below 1 Ω
O22-2 (FE) - H6-24 (FE&B) Always Below 1 Ω
O22-1 (FV) or H6-14 (FV) - Body ground Always 10 kΩ or higher
O22-3 (FS) or H6-31 (FR) - Body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.

Measure the resistance according to the value(s) in the table below.

E437279C05
1.667,0.333 2.083,0.583 0.417,0.25 5,0.333 5.417,0.583 0.417,0.25 1.042,1.521 1.542,1.521 true 2.219,1.521 2.719,1.521 true 1.24,0.948 1.813,1.417 true 1.75,0.406 2.208,0.604 0.458,0.198 10 false O22 5.177,0.385 5.333,0.583 0.156,0.198 10 false A 0.854,1.458 1.167,1.656 0.313,0.198 10 false FS 1.01,0.865 1.323,1.063 0.313,0.198 10 false FE 2.76,1.448 3.073,1.646 0.313,0.198 10 false FV 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
O22-1 (FV) - A-3 Always Below 1 Ω
O22-2 (FE) - A-2 Always Below 1 Ω
O22-3 (FS) - A-1 Always Below 1 Ω
O22-1 (FV) - O22-3 (FS) or A-3 - A-1 Always 10 kΩ or higher
O22-1 (FV) - O22-2 (FE) or A-3 - A-2 Always 10 kΩ or higher
O22-2 (FE) - O22-3 (FS) or A-2 - A-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

6.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sub Fuel Input Sub fuel input Min.: 0.00 L, Max.: 655.35 L or Unset Fuel sender input value -
Body Electrical > Combination Meter > Data List
Tester Display
Sub Fuel Input
50003 409 21

Result:
Result Proceed to
Fuel level data can be displayed on the GTS. A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the O23 fuel tank vent tube assembly connector.


b.

Disconnect the H6 combination meter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O23-3 (FR) - H6-13 (FR2) Always Below 1 Ω
O23-1 (FV) - H6-14 (FV) Always Below 1 Ω
O23-2 (FE) - H6-24 (FE&B) Always Below 1 Ω
O23-3 (FR) or H6-13 (FR2)- Body ground Always 10 kΩ or higher



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

OK

9.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY

9.INSPECT FUEL TANK VENT TUBE ASSEMBLY
a.

Measure the resistance according to the value(s) in the table below.

E437279C09
1.667,0.333 2.083,0.583 0.417,0.25 5,0.333 5.417,0.583 0.417,0.25 1.042,1.521 1.542,1.521 true 2.219,1.521 2.719,1.521 true 1.354,1.01 1.813,1.427 true 1.75,0.396 2.208,0.594 0.458,0.198 10 false O23 5.177,0.385 5.333,0.583 0.156,0.198 10 false B 0.854,1.458 1.167,1.656 0.313,0.198 10 false FR 1.125,0.927 1.438,1.125 0.313,0.198 10 false FE 2.76,1.448 3.073,1.646 0.313,0.198 10 false FV 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
O23-1 (FV) - B-3 Always Below 1 Ω
O23-2 (FE) - B-2 Always Below 1 Ω
O23-3 (FR) - B-1 Always Below 1 Ω
O23-1 (FV) - O23-2 (FE) or B-3 - B-1 Always 10 kΩ or higher
O23-1 (FV) - O23-3 (FR) or B-3 - B-2 Always 10 kΩ or higher
O23-2 (FE) - O23-3 (FR) or B-2 - B-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

10.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0.00 L, Max.: 655.35 L or Unset Fuel sender input value -
Sub Fuel Input Sub fuel input Min.: 0.00 L, Max.: 655.35 L or Unset Fuel sender input value -
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
Sub Fuel Input
50003 409 20,21

Result:
Result Proceed to
Fuel level data can be displayed on the GTS. A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY AND FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY AND FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the O22 fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the O23 fuel tank vent tube assembly connector.


c.

Disconnect the H6 combination meter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O22-1 (FV) - H6-14 (FV) Always Below 1 Ω
O22-2 (FE) - H6-24 (FE&B) Always Below 1 Ω
O23-1 (FV) - H6-14 (FV) Always Below 1 Ω
O23-2 (FE) - H6-24 (FE&B) Always Below 1 Ω
O22-1 (FV), O23-1 (FV) or H6-14 (FV)- Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR