The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield glass removal/installation are shown below.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane tracing assist system, road sign assist system, pre-collision system, front camera system or auto high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
1.REMOVE WINDSHIELD WIPER MOTOR AND LINK
8646C
2.REMOVE FORWARD RECOGNITION CAMERA
86401
3.REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
87810
4.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
w/o EC Mirror:
Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/o EC Mirror)>REMOVAL
w/ EC Mirror:
Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/ EC Mirror)>REMOVAL
62312B
5.SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Separate the front door opening trim weatherstrip LH.
62311B
6.SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
7.REMOVE FRONT PILLAR GARNISH LH
62211
8.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
81260A
9.REMOVE MAP LIGHT ASSEMBLY
74320
10.REMOVE VISOR ASSEMBLY LH
74310
11.REMOVE VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
74348C
12.REMOVE VISOR HOLDER
74612
13.REMOVE ASSIST GRIP COVER
74610A
14.REMOVE ASSIST GRIP SUB-ASSEMBLY
63311C
15.SEPARATE ROOF HEADLINING
Slightly lower the front section of the roof headlining so that the windshield glass can be removed.
Do not damage the roof headlining or vehicle interior.
It is not necessary to completely remove the roof headlining.
75533G
16.REMOVE WINDSHIELD OUTSIDE MOULDING
| *a | Cut |
Using a knife, cut off the windshield outside moulding as shown in the illustration.
Be careful not to damage the windshield glass and exterior ornaments.
56111
17.REMOVE WINDSHIELD GLASS
|
Protective Tape |
Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.
| *a | Matchmark |
Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.
Matchmarks are not necessary if the windshield glass is not going to be reused.
| *1 | Windshield Glass Stopper |
| *a | Piano wire |
Pass a piano wire between the vehicle body and windshield glass from the interior.
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut the adhesive by pulling the piano wire around the windshield glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the instrument panel safety pad sub-assembly from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel safety pad sub-assembly.
Disengage the windshield glass stoppers.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting the adhesive.
To prevent the windshield glass rom falling when performing this operation, be sure to hold the windshield glass using suction cups.
Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.
Using suction cups, remove the windshield glass.
Be careful not to drop the windshield glass.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass.
56117A
18.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the window glass adhesive dam.
Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new one.
56115A
19.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.
56116C
20.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the No. 2 windshield glass stoppers with new ones.
56115A
21.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 windshield glass stoppers from the vehicle body.
Be sure to replace the No. 1 windshield glass stoppers with new ones.