Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model RHD) › from 2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432279 BRAKE BOOSTER(for Gasoline Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for 1KR-FE, G16E-GTS)

Hide 3.REMOVE BATTERY

Hide 55606 4.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 6.LOOSEN CLEVIS LOCK NUT

a.
C142634C01
1.948,1.146 1.75,1.667 1.75,1.667 1.5,1.667 false 2.365,1.135 2.781,1.135 true 1.323,1.604 1.635,1.76 0.313,0.156 10 *1 2.833,1.073 3.146,1.229 0.313,0.156 10 *2
*1 Clevis Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the clevis lock nut of the brake master cylinder push rod clevis.


Hide 47101A 7.REMOVE BRAKE PEDAL RETURN SPRING

Hide 12601B 9.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for G16E-GTS)

Hide 164A2 10.SEPARATE RESERVE SEALED TANK (for G16E-GTS)

a.
C444957

Remove the 2 bolts to separate the reserve sealed tank.


Hide 51451A 11.REMOVE CENTER ENGINE UNDER COVER (for M15A-FKS)

Hide 55225C 12.REMOVE DASH PANEL HEAT INSULATOR (for M15A-FKS)

a.

for M15A-FKS:

i.
C429873N01
0.469,0.792 0.625,0.99 0.156,0.198 10 true A 2.688,0.344 2.844,0.542 0.156,0.198 10 true B 2.875,1.938 3.031,2.135 0.156,0.198 10 true B

Remove the nut (A).


ii.

Remove the 2 nuts (B).



Hide 88710E 13.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE)

a.
I116394

Remove the bolt.


b.
I115662

Rotate the hook connector and disconnect the air conditioning tube and accessory assembly as shown in the illustration.


c.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



d.
C436812

Disengage the clamp to separate the air conditioning tube and accessory assembly.


Hide 88710E 14.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for G16E-GTS)

a.
C445011

Remove the bolt.


b.
C445012

Rotate the hook connector and disconnect the air conditioning tube and accessory assembly as shown in the illustration.


c.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



d.
C445013

Disengage the 2 clamps to separate the air conditioning tube and accessory assembly.


Hide 44750 15.SEPARATE VACUUM HOSE ASSEMBLY (for G16E-GTS)

a.
C445017

Slide the clip and disconnect the brake booster hose from the brake booster assembly.


b.
C445018

Remove the 3 nuts to separate the vacuum hose assembly.


Hide 44772 16.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (except G16E-GTS)

a.
C439821C01
0.083,2.583 0.375,2.823 0.292,0.24 12 true *B 0.083,0.083 0.375,0.323 0.292,0.24 12 true *A
*A for M15A-FKS
*B for 1KR-FE


Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 17.SEPARATE BRAKE LINE (for G16E-GTS)

a.
C445378

Using a union nut wrench, disconnect the front No. 1 brake tube and front No. 2 brake tube from the brake actuator assembly.


b.

Disengage the 10 clamps to remove the 2 No. 4 brake tube clamps from the brake lines.


c.
C445014

Disengage the 3 clamps to separate the brake lines from the No. 2 brake tube clamp.


d.
C445015

Disengage the clamp to remove the No. 2 brake tube clamp from the vehicle body.


e.
C445016

Disengage the 6 clamps to remove the 2 No. 1 brake tube clamps from the brake lines.


Hide 18.SEPARATE BRAKE LINE (except G16E-GTS)

a.
C429016

Using a union nut wrench, disconnect the front No. 1 brake tube and front No. 2 brake tube from the brake actuator assembly.


b.

Disengage the 10 clamps to remove the 2 No. 5 brake tube clamps from the brake lines.


c.

for Manual Transaxle:

i.
C435050

Disengage the clamp to separate the clutch master cylinder to flexible hose tube from the No. 2 brake tube clamp.



d.
C432450

Disengage the 3 clamps to separate the brake lines from the No. 2 brake tube clamp.


e.
C432451

Disengage the clamp to remove the No. 2 brake tube clamp from the vehicle body.


f.
C432452

Disengage the 6 clamps to remove the 2 No. 1 brake tube clamps from the brake lines.


Hide 44610 19.REMOVE BRAKE BOOSTER ASSEMBLY

a.

w/ Vacuum Warning Switch:

i.
C439822C01
0.052,2.5 0.333,2.74 0.281,0.24 12 true *B 0.083,0.083 0.365,0.323 0.281,0.24 12 true *A
*A for TMC Made
*B for TMMF Made


Disconnect the vacuum warning switch connector.



b.

w/ Vacuum Sensor:

i.
C436822

Disconnect the vacuum sensor connector.



c.
C435051C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the vehicle body.


d.
C435054

Remove the 4 nuts.


e.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


f.
C435055

Move aside the front No. 1 brake tube and front No. 2 brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the brake tubes.



g.

Remove the brake booster assembly.


Hide 44785 20.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.