Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model RHD) › from 2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432279 BRAKE BOOSTER(for Gasoline Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model RHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



b.

Return the front No. 1 brake tube and front No. 2 brake tube to their original positions.

NOTICE:

Do not apply excessive force to the brake tubes.



c.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



d.
C435054N01
0.583,1.333 0.781,1.531 0.198,0.198 10 true 1 2.75,0.604 2.948,0.802 0.198,0.198 10 true 2 0.604,0.594 0.802,0.792 0.198,0.198 10 true 3 2.76,1.333 2.958,1.531 0.198,0.198 10 true 4

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the 4 nuts in the order shown in the illustration.



e.

Remove the protective tape.


f.

w/ Vacuum Warning Switch:

i.

Connect the vacuum warning switch connector.



g.

w/ Vacuum Sensor:

i.

Connect the vacuum sensor connector.



Hide 3.INSTALL BRAKE LINE (for G16E-GTS)

a.
C445016

Engage the 6 clamps to install the 2 new No. 1 brake tube clamps to the brake lines.


b.
C445015

Engage the clamp to install a new No. 2 brake tube clamp to the vehicle body.


c.
C445014

Engage the 3 clamps to install the brake lines to the No. 2 brake tube clamp.


d.
C445379C01
1.771,4.229 2.083,4.427 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Engage the 10 clamps to install 2 new No. 4 brake tube clamps to the brake lines.


e.

Temporarily install the front No. 1 brake tube and front No. 2 brake tube to the correct position on the brake actuator assembly.


f.

Using a union nut wrench, tighten the front No. 1 brake tube and front No. 2 brake tube.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 4.INSTALL BRAKE LINE (except G16E-GTS)

a.
C432452

Engage the 6 clamps to install the 2 new No. 1 brake tube clamps to the brake lines.


b.
C432451

Engage the clamp to install a new No. 2 brake tube clamp to the vehicle body.


c.
C432450

Engage the 3 clamps to install the brake lines to the No. 2 brake tube clamp.


d.

for Manual Transaxle:

i.
C435050

Engage the clamp to install the clutch master cylinder to flexible hose tube to the No. 2 brake tube clamp.



e.
C435057C01
1.771,4.229 2.083,4.427 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Engage the 10 clamps to install 2 new No. 5 brake tube clamps to the brake lines.


f.

Temporarily install the front No. 1 brake tube and front No. 2 brake tube to the correct position on the brake actuator assembly.


g.

Using a union nut wrench, tighten the front No. 1 brake tube and front No. 2 brake tube.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 44750 5.INSTALL VACUUM HOSE ASSEMBLY (for G16E-GTS)

a.

Install the vacuum hose assembly with the 3 nuts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


b.
C445017C01
1.656,0.979 2.208,0.729 true 2.188,0.656 2.427,0.854 0.24,0.198 10 true *a
*a Paint Mark


Connect the brake booster hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, make sure that the paint mark is facing the front of the vehicle.

·

Make sure that the tabs of the clip are facing the front of the vehicle.




Hide 44772 6.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (except G16E-GTS)

a.

for M15A-FKS:

i.
C436813C01
1.396,1.01 0.667,0.698 true 0.417,0.604 0.667,0.833 0.25,0.229 10 true *a
*a Paint Mark


Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, face the paint mark up.

·

Make sure that the tabs of the clip are facing upward.





b.

for 1KR-FE:

i.
C436814C01
1.302,1.073 0.615,1.021 true 0.354,0.896 0.604,1.125 0.25,0.229 10 true *a
*a Paint Mark


Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, make sure that the paint mark is facing the front of the vehicle.

·

Make sure that the tabs of the clip are facing the front of the vehicle.





Hide 88710E 7.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for G16E-GTS)

a.

Engage the 2 clamps to install the air conditioning tube and accessory assembly.


b.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


c.

Apply sufficient compressor oil to 2 new O-rings and fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

HFC-134a(R134a):

ND-OIL 8 or equivalent

HFO-1234yf(R1234yf):

ND-OIL 12 or equivalent



d.

Install the 2 O-rings to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



e.

Connect the air conditioning tube and accessory assembly.


f.
C445019

Rotate the hook connector as shown in the illustration.


g.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 88710E 8.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for 1KR-FE)

a.

Engage the clamp to install the air conditioning tube and accessory assembly.


b.

Remove the vinyl tape from the air conditioning tube and accessory assembly.


c.

Apply sufficient compressor oil to 2 new O-rings and fitting surface of the air conditioning tube and accessory assembly.

Compressor Oil:

HFC-134a(R134a):

ND-OIL 8 or equivalent

HFO-1234yf(R1234yf):

ND-OIL 12 or equivalent



d.

Install the 2 O-rings to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



e.

Connect the air conditioning tube and accessory assembly.


f.
I115836

Rotate the hook connector as shown in the illustration.


g.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 55225C 9.INSTALL DASH PANEL HEAT INSULATOR (for M15A-FKS)

a.
C429873N01
0.469,0.792 0.625,0.99 0.156,0.198 10 true A 2.688,0.344 2.844,0.542 0.156,0.198 10 true B 2.875,1.938 3.031,2.135 0.156,0.198 10 true B

Temporarily install the dash panel heat insulator to the vehicle body with the 2 nuts (B).

i.

Install the nut (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Tighten the 2 nuts (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51451A 10.INSTALL CENTER ENGINE UNDER COVER (for M15A-FKS)

Hide 164A2 11.INSTALL RESERVE SEALED TANK (for G16E-GTS)

a.

Install the reserve sealed tank with the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 12601B 12.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (for G16E-GTS)

Hide 47101A 14.INSTALL BRAKE PEDAL RETURN SPRING

Hide 55606 16.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 19.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for 1KR-FE, G16E-GTS)

Hide 21.INSPECT FOR REFRIGERANT LEAK (for 1KR-FE, G16E-GTS)