Home › Engine / Hybrid System › G16E-GTS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.09
RM36W0E _51 Engine / Hybrid System _095252 G16E-GTS ENGINE MECHANICAL _0447813 ENGINE ASSEMBLY A

G16E-GTS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>G16E-GTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 3.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 31001 5.INSTALL COVER AND DISC CLUTCH SET

Hide 37117B 7.INSTALL PROPELLER SHAFT HEAT INSULATOR

Hide 25051 8.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 82121 9.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


b.
A479712

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A479711

Install the 4 bolts.

Torque:
Bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt (B) : 20 N*m (204 kgf*cm, 15 ft.*lbf)


d.
A479710

Install the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16620D 11.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16361A 12.INSTALL FAN AND GENERATOR V BELT

Hide 11363A 13.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the cylinder block sub-assembly.


Hide 23826 15.INSTALL NO. 1 FUEL VAPOR FEED HOSE

a.

Engage the 2 clamps.


b.

Install the No. 1 fuel vapor feed hose to the purge valve (purge VSV).


Hide 12305 16.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A479706C01
0.115,1.302 0.708,1.521 0.594,0.219 10 true 1 (*a), 4 2.792,1 2.979,1.198 0.188,0.198 10 true 2 1.885,0.042 2.073,0.24 0.188,0.198 10 true 3
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Connect the air conditioner tube with the clamp.


Hide 164A2 17.INSTALL RESERVE TANK ASSEMBLY

a.

Install the 2 bplts and reserve tank assembly to the vehicle.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Engage the clamp.


c.

Connect the No. 3 water by-pass hose to the reserve tank assembly and slide the clip to secure it.


Hide 12372A 18.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A479703C01
0.021,0.927 0.625,1.125 0.604,0.198 10 true 1 (*a), 5 2.49,1.99 2.656,2.167 0.167,0.177 10 true 2 0.813,1.979 0.979,2.156 0.167,0.177 10 true 3 2.896,0.917 3.063,1.094 0.167,0.177 10 true 4 1.313,0.063 1.479,0.24 0.167,0.177 10 true 6
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 5. bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
A479702

Engage the clamp.


Hide 20.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A479700

Connect the front suspension crossmember sub-assembly to the vehicle with the 8 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


d.
A479698N01
2.406,1.594 2.563,1.792 0.156,0.198 10 true 1 2.427,1.094 2.583,1.292 0.156,0.198 10 true 3 2.438,0.854 2.594,1.052 0.156,0.198 10 true 2

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts in the order shown illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


e.
A479699N01
0.635,1.25 0.792,1.448 0.156,0.198 10 true 1 0.844,0.219 1,0.417 0.156,0.198 10 true 2 0.854,1.646 1.01,1.844 0.156,0.198 10 true 3 0.625,0.646 0.781,0.844 0.156,0.198 10 true 4

Install the engine mounting insulator LH to the engine mounting bracket LH with the 4 bolts in the order shown illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 31481A 21.INSTALL NO. 1 CLUTCH HOSE

a.
A479752C01
2.167,2.125 1.646,1.385 true 2.198,2.135 2.51,2.333 0.313,0.198 10 false *a 0.917,1.865 1.146,2.052 0.229,0.188 10 true *b
*a 10 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.


b.

Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 17361J 22.INSTALL NO. 1 AIR TUBE

a.

Install the No. 1 air tube with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Tighten the 2 hose clamp.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 37100 24.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 45260 25.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 26.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 27.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 88711 28.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 23901 30.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A479696

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>G16E-GTS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A479695

Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.


Hide 16290F 32.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 23826 33.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the fuel tank to canister tube.


Hide 16264 34.INSTALL NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the No. 4 water by-pass pipe and slide the clip to secure it.


Hide 16261G 35.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the No. 4 water by-pass pipe and slide the clip to secure it.


Hide 44774 36.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 33820B 37.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
A481177C01
1.615,0.76 2,0.396 2,0.396 1.896,0.927 true 1.979,0.135 2.167,0.333 0.188,0.198 10 true *a 2.563,0.031 2.75,0.229 0.188,0.198 10 true B 1.208,0.104 1.396,0.302 0.188,0.198 10 true B 1.021,1.844 1.208,2.042 0.188,0.198 10 true A 1.979,1.719 2.167,1.917 0.188,0.198 10 true A
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.



b.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).


Hide 17362B 39.INSTALL NO. 2 AIR TUBE

a.
A479691

Install the No. 2 air hose with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Tighten the hose 2 clamps.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 16572D 40.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.


Hide 16571C 41.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 42.CONNECT ENGINE WIRE

a.

Engage the 2 claws to the engine room relay block.


b.

Connect the 3 connectors to the engine room relay block.


c.

Install the 2 nut.

Torque:
Nut (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut (B) : 7.6 N*m (77 kgf*cm, 67 in.*lbf)


d.

Engage the clamp to connect the engine wire to the vehicle.


e.

Connect the engine wire to the vehicle with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82672 43.INSTALL JUNKTION BLOCK COVER

a.

Install the junktion block cover.


Hide 82662A 44.INSTALL NO. 1 RELAY BLOCK COVER

a.

Install the No. 1 relay block cover.


Hide 17771A 45.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Engage the clamp to the air cleaner bracket.


Hide 46.INSTALL AIR CLEANER ASSEMBLY

a.

Install the air cleaner assembly and tighten the hose clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


b.

Connect the vacuum hose assembly and vacuum transmittinghose.


c.

Install the 2 clips.


d.

Connect the clamp.


e.

Connect the mass air flow meter connector.


f.

Engage the clamp to the air cleaner assembly.


g.

Connect the vacuum switching valve connector.


Hide 55701J 47.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 48.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55815E 49.INSTALL NO. 1 FRONT VENTILATOR SEAL (for LHD)

Hide 55815E 50.INSTALL NO. 1 FRONT VENTILATOR SEAL (for RHD)

Hide 55734A 51.INSTALL WATER GUARD PLATE RH (for LHD)

Hide 55735A 52.INSTALL WATER GUARD PLATE LH (for RHD)

Hide 53.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 12601B 54.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A479678

Engage the 4 clamps to install the No. 1 engine cover sub-assembly.

NOTICE:
·

Securely engage the clamps.

·

If the clamps are forcibly engaged or struck with an object, they may be damaged.




Hide 57.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 59.ADD ENGINE COOLANT

Hide 60.ADD MANUAL TRANSAXLE OIL

Hide 61.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 64.INSPECT FOR ENGINE OIL LEAK

Hide 65.INSPECT MANUAL TRANSAXLE OIL LEAK

Hide 71.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 51447D 72.INSTALL CENTER NO. 4 ENGINE UNDER COVER

Hide 51410 75.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 76.INSTALL FRONT WHEELS

Hide 77. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 78.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT