Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL › from 2020.09
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0447535 REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear drive shaft oil seal replacement are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Tire ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) Active torque split AWD system (Click here)
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
Rear wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 2.REMOVE REAR DRIVE SHAFT OIL SEAL

a.
C440333C02
1.552,0.76 1.75,0.417 1.75,0.417 1.917,0.417 true 1.333,2.396 1.5,2.396 1.5,2.396 1.583,2.646 false 2.5,3.25 2.833,3.25 2.833,3.25 2.833,3.083 true 1.958,0.354 2.271,0.552 0.313,0.198 10 true SST 1.021,2.313 1.479,2.51 0.458,0.198 10 false SST 2.333,3.198 2.552,3.385 0.219,0.188 10 false *1
*1 Rear Drive Shaft Oil Seal


Using SST, remove the rear drive shaft oil seal from the rear differential carrier assembly.

SST
09308-00010  


Hide 3.INSTALL REAR DRIVE SHAFT OIL SEAL

a.
C440334C03
1.042,2.375 1.667,2.375 1.667,2.375 1.667,2.625 false 1.417,2.385 1.417,2.635 false 2.083,1.167 2.083,1.333 2.083,1.333 1.833,1.333 true 1.667,1.167 2.25,1.167 true 2.063,3.052 1.729,3.052 false 1.563,2.958 1.875,3.115 0.313,0.156 10 false *1 1.719,2.292 1.833,2.448 0.115,0.156 10 true A 0.708,2.292 1.021,2.448 0.313,0.156 10 false SST 2.292,1.083 2.604,1.25 0.313,0.167 10 true SST
*1 Rear Drive Shaft Oil Seal


Using SST and a hammer, install a new rear drive shaft oil seal into the rear differential carrier assembly.

SST
09223-46011  
09631-32020  

NOTICE:
·

Install the rear drive shaft oil seal uniformly so that it is driven in straight.

·

Do not excessively tap in the rear drive shaft oil seal.

·

Do not damage the rear drive shaft oil seal.

·

Make sure to install the rear drive shaft oil seal as specified, otherwise a malfunction such as an oil leak may occur.



Standard Distance (A):

8.2 to 8.8 mm (0.323 to 0.346 in.)



b.

Apply a light coat of MP grease to the lip of the new rear drive shaft oil seal.