Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER › from 2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0447928 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 41101 1.REMOVE REAR DIFFERENTIAL CARRIER SUB-ASSEMBLY

Hide 48812 2.REMOVE REAR STABILIZER BAR

Hide 51206A 3.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C450300

Disengage the clamp to separate the differential carrier wire harness.


b.
C450301

Disengage the clamp to separate the differential carrier wire harness.


c.
C450302

Disengage the clamp to separate the differential carrier wire harness.


d.
C445856C01
1.979,2.771 2.26,2.219 true 2.385,2.656 2.635,2.469 true 0.823,2.719 1.021,2.365 true 1.719,2.667 2.104,1.885 true 2.615,3.094 2.75,2.833 true 2.677,2.302 2.906,2.531 0.229,0.229 10 true *b 2.271,2.073 2.5,2.302 0.229,0.229 10 true *b 2.135,1.75 2.365,1.979 0.229,0.229 10 true *b 1.042,2.208 1.271,2.448 0.229,0.24 10 true *b 2.771,2.688 3,2.917 0.229,0.229 10 false *a
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C442150


·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.



e.

Remove the 2 bolts and 2 nuts.


f.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48790 4.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 5.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 41651 6.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

Hide 51284 7.REMOVE REAR SUSPENSION MEMBER HOLE COVER

a.
C445857C01
0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.094,1.51 0.406,1.708 0.313,0.198 10 false *b
*a for LH Side
*b for RH Side


Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.


Hide 8.REMOVE HOLE PLUG

a.
C445858

Remove the 8 hole plugs from the rear suspension member sub-assembly as shown in the illustration.