Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for G16E-GTS) › from 2020.09
RM36W0E _52 Drivetrain _087547 DRIVE SHAFT / PROPELLER SHAFT _0447996 FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for G16E-GTS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Calibration
·

DTCs are stored

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442C 3.REMOVE ENGINE UNDER COVER LH

Hide 51441C 4.REMOVE ENGINE UNDER COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 5.DRAIN MANUAL TRANSAXLE OIL

Hide 6.DRAIN TRANSFER OIL

Hide 43502H 7.REMOVE FRONT AXLE SHAFT NUT

a.
C445299N01
2.542,1.719 2.542,1.479 false 2.427,1.729 2.885,1.927 0.458,0.198 10 false SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the front drive shaft assembly may be damaged.



b.

Using a 30 mm deep socket wrench, remove the front axle shaft nut while applying the brakes.


Hide 45047 9.SEPARATE TIE ROD END SUB-ASSEMBLY

Hide 48810 10.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 48069 11.SEPARATE FRONT LOWER NO.1 SUSPENSION ARM SUB-ASSEMBLY

Hide 43420 12.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C445300C01
2.677,0.479 2.854,0.542 2.854,0.542 2.75,0.719 true 2.875,0.448 3.063,0.646 0.188,0.198 10 true *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.
C445301

Using a plastic hammer, separate the front drive shaft assembly from the front axle hub sub-assembly.

NOTICE:
·

Do not push the front axle hub sub-assembly towards the outside of the vehicle any further than necessary.

·

Do not damage the front axle outboard joint boot.

·

Do not deform the front disc brake dust cover.

·

Do not damage the deflector.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle hub sub-assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 43420 13.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C445302N01
2.063,1.604 1.51,1.813 1.51,1.813 1.969,1.292 true 1.208,1.75 1.563,1.948 0.354,0.198 10 false SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01011  
09520-20010  (09521-02010, 09521-02040, 09521-02060)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot LH.

·

Do not drop the front drive shaft assembly LH.

·

When removing the front drive shaft assembly LH, keep it level.




Hide 43410 14.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C445303

Separate the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.


b.

Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Do not damage the transfer case oil seal RH.

·

Do not damage the front drive shaft oil seal RH.

·

Do not drop the front drive shaft assembly RH.

·

When removing the front drive shaft assembly RH, keep it level.



HINT:

If the spline connection is stiff, using a brass bar and hammer, lightly tap the inboard joint assembly to remove it.



Hide 43420G 15.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

a.
C264437

Using a screwdriver, remove the front drive shaft hole snap ring LH from the front drive shaft assembly LH.


Hide 43457B 16.REMOVE DRIVE SHAFT BEARING BRACKET HOLE SNAP RING

a.
C445304

Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.