Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM J

G16E-GTS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the clutch start switch assembly and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

2.READ VALUE USING GTS (STARTER SW)

B

17.READ VALUE USING GTS (STARTER SW)
2.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal.


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result
NG
OK



NG

3.CHECK STOP AND START SYSTEM

OK

10.INSPECT ST NO. 1 RELAY
3.CHECK STOP AND START SYSTEM

Result:
Result
OK
NG



OK

4.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR STOP AND START SYSTEM

4.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

5.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

7.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A106-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A106-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
A67-17 (CLL) - A106-23 (NSW) Always Below 1 Ω
H45-10 (STAR), A67-17 (CLL), A106-23 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A106-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A64-1 (L), 2 (ST NO. 1 relay), A67-21 (STA) or A106-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the clutch start switch assembly connector.


d.

Disconnect the engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) - A67-17 (CLL) Always Below 1 Ω
H54-4 (ST2) - A106-23 (NSW) Always Below 1 Ω
H54-4 (ST2), A106-23 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>G16E-GTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

10.INSPECT ST NO. 1 RELAY
a.

Inspect the ST NO. 1 relay.

Click hereEngine / Hybrid System>G16E-GTS (STARTING)>RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

11.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

11.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>G16E-GTS (STARTING)>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - D54-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D80-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A468643C03
0.042,0.021 0.354,0.177 0.313,0.156 10 false *1 1.906,2.073 2.219,2.229 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO 1 RELAY)

15.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - A64-1 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal.


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
OK A
NG B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)