Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.09
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C13807F Stop Lamp Relay Actuator Stuck Off Either of the following is detected:
·

When the IGR terminal voltage exceeds 10 V and the +BS terminal voltage is from 9.5 to 17.4 V, stop light drive output (STPO) is ON, STP is OFF and STP2 is OFF continuously for 2 seconds or more.

·

When the IGR terminal voltage exceeds 10 V and the +BS terminal voltage is 9.5 V or higher, stop light drive output (STPO) is OFF, STP is ON and STP2 is OFF continuously for 5 seconds or more.


·

Wire harness and connector

·

Skid control ECU (Brake actuator assembly)

·

Rear combination light lens and body LH

·

Rear combination light lens and body RH

·

Center stop light assembly


Brake

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.CHECK VEHICLE SPECIFICATION (FOR HALOGEN HEADLIGHT)
a.

Check the vehicle specification.


Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B



A

2.CHECK STOP LIGHT OPERATION (FOR HALOGEN HEADLIGHT)

B

12.CHECK VEHICLE SPECIFICATION
2.CHECK STOP LIGHT OPERATION (FOR HALOGEN HEADLIGHT)
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

7.READ VALUE USING GTS (STOP LIGHT RELAY)
3.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Perform the Active Test of the stop light relay using the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Restrict Condition Diagnostic Note
Stop Lamp Relay STPO terminal output OFF / ON Vehicle condition:
Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


-

Chassis > Brake > Active Test
Tester Display
Stop Lamp Relay
50004 435 27
b.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-26 (STPO) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-4 (ACC) - A36-26 (STOP) Always Below 1 Ω



Post-procedure1

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the T4 rear combination light lens and body LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

8.READ VALUE USING GTS (STOP LIGHT RELAY)
8.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the S2 rear combination light lens and body RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

9.READ VALUE USING GTS (STOP LIGHT RELAY)
9.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the X2 center stop light assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-3 (L) - A36-5 (STP2) Always Below 1 Ω
A63-3(L) or A36-5 (STP2) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for 3 Door A
for 5 Door B



A

13.CHECK STOP LIGHT OPERATION (FOR LED HEADLIGHT)

B

23.CHECK STOP LIGHT OPERATION (FOR LED HEADLIGHT)
13.CHECK STOP LIGHT OPERATION (FOR LED HEADLIGHT)
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

14.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

18.READ VALUE USING GTS (STOP LIGHT RELAY)
14.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Perform the Active Test of the stop light relay using the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Restrict Condition Diagnostic Note
Stop Lamp Relay STPO terminal output OFF / ON Vehicle condition:
Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


-
Chassis > Brake > Active Test
Tester Display
Stop Lamp Relay
50004 435 27

b.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

16.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)
15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A108-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A108-26 (STPO) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-4 (ACC) - A108-26 (STOP) Always Below 1 Ω



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the O109 rear combination light lens and body LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

19.READ VALUE USING GTS (STOP LIGHT RELAY)
19.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the O110 rear combination light lens and body RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

20.READ VALUE USING GTS (STOP LIGHT RELAY)
20.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the g1 center stop light assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

B

21.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
21.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A108 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A108-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

22.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
22.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-3 (L) - A108-5 (STP2) Always Below 1 Ω
A63-3 (L) or A108-5 (STP2) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK STOP LIGHT OPERATION (FOR LED HEADLIGHT)
a.

Check that the stop lights come on when the brake pedal is depressed.

OK:

The stop lights illuminate.



Result:
Proceed to
OK
NG



OK

24.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

28.READ VALUE USING GTS (STOP LIGHT RELAY)
24.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Perform the Active Test of the stop light relay using the GTS.

Chassis > Brake > Active Test
Tester Display Measurement Item Restrict Condition Diagnostic Note
Stop Lamp Relay STPO terminal output OFF / ON Vehicle condition:
Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


-
Chassis > Brake > Active Test
Tester Display
Stop Lamp Relay
50004 435 27

b.

According to the display on the GTS, perform the Active Test and check the operation of the stop lights.

OK:

Stop lights turn on in accordance with the Active Test.



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

NG

26.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)
25.CHECK HARNESS AND CONNECTOR (STOP LIGHT SIGNAL INPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (STOP LIGHT ILLUMINATION OUTPUT CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-26 (STPO) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

27.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
27.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-4 (ACC) - A36-26 (STOP) Always Below 1 Ω



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the T2 rear combination light lens and body LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

29.READ VALUE USING GTS (STOP LIGHT RELAY)
29.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the S4 rear combination light lens and body RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

GO TO LIGHTING SYSTEM

Refer to "Left or right stop light does not illuminate" of problem symptoms table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE


B

30.READ VALUE USING GTS (STOP LIGHT RELAY)
30.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the X2 center stop light assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake > Data List
Tester Display
Stop Light Relay
50003 435 67

e.

With the brake pedal released, check the value of Data List item "Stop Light Relay".


Post-procedure1

f.

Turn the ignition switch off.


Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



A

B

31.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
31.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-5 (STP2) - Body ground Brake pedal depressed 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

32.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
32.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A63 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-3 (L) - A36-5 (STP2) Always Below 1 Ω
A63-3 (L) or A36-5 (STP2) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR