Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2021.04
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424238 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

for Radio and Display Type without TAS Type


C430904E01
5.646,4.958 6.844,5.5 1.198,0.542 10 false Radio and Display Receiver Assembly 5.833,0.656 6.448,0.854 0.615,0.198 10 false CANH 5.833,1.198 6.448,1.396 0.615,0.198 10 false CANL 5.833,2.521 6.448,2.719 0.615,0.198 10 false +B1 5.833,4.552 6.448,4.75 0.615,0.198 10 false GND1 5.833,3.906 6.448,4.104 0.615,0.198 10 false IG 5.833,3.198 6.448,3.396 0.615,0.198 10 false ACC1 5.427,0.635 6.042,0.833 0.615,0.198 10 false H80 5.417,1.167 6.031,1.365 0.615,0.198 10 false H80 5.417,2.531 6.031,2.729 0.615,0.198 10 false H79 5.427,3.188 6.042,3.385 0.615,0.198 10 false H79 5.406,3.917 6.021,4.115 0.615,0.198 10 false H80 5.438,4.563 6.052,4.76 0.615,0.198 10 false H79 5.438,0.406 5.698,0.604 0.26,0.198 10 false 13 5.5,4.354 5.656,4.552 0.156,0.198 10 false 1 5.458,3.708 5.76,3.917 0.302,0.208 10 false 19 5.458,2.99 5.75,3.188 0.292,0.198 10 false 15 5.479,2.323 5.635,2.521 0.156,0.198 10 false 4 5.458,0.969 5.698,1.167 0.24,0.198 10 false 14 1.667,0.531 1.969,0.75 0.302,0.219 10 false 3 1.656,1.073 2.01,1.271 0.354,0.198 10 false 14 0.146,1.708 3.052,2.063 2.906,0.354 10 false No. 4 Global CAN Junction Connector 0.135,1.552 0.75,1.75 0.615,0.198 10 false H115 4.188,4.094 5.302,4.438 1.115,0.344 10 false ECU-IGR NO. 2 2.135,3.875 3.875,4.177 1.74,0.302 10 false from IGR-NO. 2 Relay 2.135,2.49 3.74,2.76 1.604,0.271 10 false from Auxiliary Battery 2.448,3.156 3.594,3.49 1.146,0.333 10 false from ACC Relay 4.333,3.354 5.448,3.698 1.115,0.344 10 false ECU-ACC 4.448,2.677 5.563,3.021 1.115,0.344 10 false RADIO


for Radio and Display Type with TAS Type


C430934E01
5.646,4.948 6.844,5.49 1.198,0.542 10 false Radio and Display Receiver Assembly 5.844,0.656 6.458,0.854 0.615,0.198 10 false CA8H 5.833,1.188 6.448,1.385 0.615,0.198 10 false CA8L 5.833,2.531 6.448,2.729 0.615,0.198 10 false +B1 5.833,4.573 6.448,4.771 0.615,0.198 10 false GND1 5.833,3.927 6.448,4.125 0.615,0.198 10 false IG 5.833,3.198 6.448,3.396 0.615,0.198 10 false ACC1 5.438,0.635 6.052,0.833 0.615,0.198 10 false H80 5.417,1.167 6.031,1.365 0.615,0.198 10 false H80 5.417,2.531 6.031,2.729 0.615,0.198 10 false H79 5.417,3.198 6.031,3.396 0.615,0.198 10 false H79 5.427,3.917 6.042,4.115 0.615,0.198 10 false H80 5.438,4.552 6.052,4.75 0.615,0.198 10 false H79 5.49,0.427 5.75,0.625 0.26,0.198 10 false 1 5.479,4.344 5.635,4.542 0.156,0.198 10 false 1 5.448,3.708 5.75,3.917 0.302,0.208 10 false 19 5.448,2.99 5.74,3.188 0.292,0.198 10 false 15 5.5,2.313 5.656,2.51 0.156,0.198 10 false 4 5.5,0.938 5.74,1.135 0.24,0.198 10 false 2 1.688,0.531 1.99,0.75 0.302,0.219 10 false 4 1.656,1.083 2.01,1.281 0.354,0.198 10 false 15 0.094,1.688 3,2.042 2.906,0.354 10 false No. 11 Global CAN Junction Connector 0.104,1.51 0.719,1.708 0.615,0.198 10 false H151 4.198,4.083 5.313,4.427 1.115,0.344 10 false ECU-IGR NO. 2 2.156,3.875 3.896,4.177 1.74,0.302 10 false from IGR-NO. 2 Relay 2.177,2.49 3.906,2.99 1.729,0.5 10 false from Auxiliary Battery 2.5,3.146 4.229,3.646 1.729,0.5 10 false from ACC Relay 4.333,3.344 5.448,3.688 1.115,0.344 10 false ECU-ACC 4.458,2.698 5.573,3.042 1.115,0.344 10 false RADIO


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Radio and Display Type without TAS Type A
for Radio and Display Type with TAS Type B



A

2.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)

B

4.CHECK OPTIONS
2.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-13 (CANH) - H80-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H79 and H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H79-1 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H80-19 (IG) - Body ground Ignition switch ON 11 to 14 V
H79-4 (+B1) - Body ground Ignition switch off 11 to 14 V
H79-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK OPTIONS
a.

Check whether dealer installed options (radio and display receiver assembly) that support CAN communication are installed.


Result:
Result Proceed to
Installed A
Not installed B



A

5.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)

B

7.BUS INSPECTION (CHECK CONNECTED RADIO AND DISPLAY RECEIVER ASSEMBLY USING GTS)
5.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-1 (CA8H) - H80-2 (CA8L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H80-4 (+B1) - Body ground Ignition switch off 11 to 14 V
H80-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
H80-19 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.BUS INSPECTION (CHECK CONNECTED RADIO AND DISPLAY RECEIVER ASSEMBLY USING GTS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

*: When a dealer-installed option is installed


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Central Gateway / Utility / Initialization.

Body Electrical > Central Gateway > Utility
Tester Display
Initialization
50005 443 4581

e.

Select "CAN Bus Check" from the screen on the GTS.

CAN Bus Check
50007

Result:
Result Proceed to
"Display and Navigation (AVN) " is not displayed A
"Display and Navigation (AVN) " is displayed B



A

END

B