Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2021.11
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432174 MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

C551 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front wheel alignment adjustment Calibration
·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


TMC Made:
(Click here)
for TMMF, TMMCZ Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 82121 1.DISCONNECT ENGINE WIRE

a.
C443577

Disconnect the back-up light switch assembly connector.


b.

Disengage the 2 clamps to separate the engine wire from the wire harness clamp brackets.


c.

w/ Stop and Start System:

i.
C443578

Disconnect the neutral position switch connector.



d.

Remove the bolt and disconnect the engine wire.


e.

Remove the 2 bolts and separate the engine wire protector.


Hide 11363A 3.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 28100 4.REMOVE STARTER ASSEMBLY

Hide 51201 5.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 6.REMOVE ENGINE MOVING CONTROL ROD BRACKET

a.
C440578

Remove the 3 bolts and engine moving control rod bracket from the manual transaxle assembly.


Hide 12325A 7.REMOVE ENGINE MOUNTING BRACKET LH

a.
C440579

Remove the 4 bolts and engine mounting bracket LH from the manual transaxle assembly.


Hide 30300 8.REMOVE MANUAL TRANSAXLE ASSEMBLY

a.
C116849

Remove the 9 bolts and manual transaxle assembly from the engine assembly.

NOTICE:
·

To prevent damage to the knock pins, do not pry between the manual transaxle assembly and engine assembly.

·

To prevent damage to the input shaft, do not forcefully shake the manual transaxle assembly.




Hide 33544C 9.REMOVE SHIFT LEVER DAMPER

a.
C242103

Remove the 2 nuts and shift lever damper from the manual transaxle assembly.


Hide 10.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C242360

Remove the 2 bolts and 2 wire harness clamp brackets from the manual transaxle assembly.


Hide 33111A 11.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C245766

Remove the manual transaxle case plug and gasket from the manual transaxle assembly.