The brake actuator assembly communicates with the ECM and engine stop and start ECU. When the brake actuator assembly does not receive data from the engine stop and start ECU, the engine stop and start ECU stores DTC U117087.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| U117087 | Lost Communication With Brake System Control Module(ch2) Missing Message | No communication from the brake actuator assembly continues. | ·
Brake actuator assembly main line or connector ·
Brake actuator assembly |
Engine stop and start ECU |
except G16E-GTS
for G16E-GTS
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.
Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
Inspect the fuses for circuits related to this system before performing the following procedure.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| except G16E-GTS | A |
| for G16E-GTS | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| H117-10 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| H117-21 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| H117-10 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| H117-21 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
| NG (+B short or Short to ground) | D |
A
B
C
D
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117087 is output | A |
| DTC U117087 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H117-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H117-22 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A37 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-19 (CA2H) - A37-18 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for TMMF Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
for TMC Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF, TMMCZ Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H40-13 (CAWL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H43-16 (LC1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H117-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H117-22 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A37 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-19 (CA2H) - A37-18 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for TMMF Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
for TMC Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF, TMMCZ Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H40-13 (CAWL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H43-16 (LC1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-20 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-9 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-20 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-22 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-11 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-22 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-21 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-10 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-21 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A37 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A37-19 (CA2H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-18 (CA2L) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A37-19 (CA2H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A37-18 (CA2L) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for TMMF Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
for TMC Made RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF, TMMCZ Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-13 (CAWL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-12 (CAWH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-13 (CAWL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-16 (LC1L) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-15 (LC1H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H43-16 (LC1L) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| H117-10 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| H117-21 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| H117-10 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| H117-21 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
| NG (+B short or Short to ground) | D |
A
B
C
D
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117087 is output | A |
| DTC U117087 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H117-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H117-22 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A108 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A108-36 (CA2H) - A108-37 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H40-13 (CAWL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H43-16 (LC1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H117-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H117-22 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H117-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A108 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A108-36 (CA2H) - A108-37 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H40-13 (CAWL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H43-16 (LC1L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-9 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-20 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-9 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-20 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-11 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-22 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-11 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-22 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H117 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H117-10 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-21 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H117-10 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H117-21 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the A108 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A108-36 (CA2H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A108-37 (CA2L) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A108-36 (CA2H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A108-37 (CA2L) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made RHD)>REMOVAL
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMC Made LHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H40 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H40-12 (CAWH) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-13 (CAWL) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H40-12 (CAWH) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H40-13 (CAWL) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU (for RHD)>REMOVAL
NG
Reconnect the H117 No. 6 global CAN junction connector.
Disconnect the H43 engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H43-15 (LC1H) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-16 (LC1L) - H3-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H43-15 (LC1H) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H43-16 (LC1L) - H3-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG