Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE (except G16E-GTS) › from 2021.11
RM36W0E _54 Brake _089430 PARKING BRAKE _0451951 PARKING BRAKE CABLE(except G16E-GTS) A

PARKING BRAKE  PARKING BRAKE CABLE(except G16E-GTS)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the parking brake cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model TMC Made)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Exhaust system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



NOTICE:
·

Immediately after installing the brake shoes, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the brake shoes, the brake pedal may feel soft due to clearance between the rear brake shoe and brake drum. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the brake shoes, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model TMC Made)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model TMC Made)



HINT:
for HV Model TMC Made:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION (for HV Model TMC Made)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 58911A 2.REMOVE NO. 1 BOX SIDE PANEL (for TMC Made)

Hide 58912C 3.REMOVE NO. 2 BOX SIDE PANEL (for TMC Made)

Hide 58903A 4.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (for TMC Made)

Hide 58857A 5.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET (for TMC Made)

Hide 58903A 6.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (for Gasoline Model TMMF, TMMCZ Made)

Hide 58911A 7.REMOVE NO. 1 BOX SIDE PANEL (for HV Model TMMF, TMMCZ Made)

Hide 58912C 8.REMOVE NO. 2 BOX SIDE PANEL (for HV Model TMMF, TMMCZ Made)

Hide 58857A 9.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET (for HV Model TMMF, TMMCZ Made)

Hide 10.LOOSEN PARKING BRAKE CABLE ASSEMBLY

Hide 11.DISCONNECT PARKING BRAKE CABLE ASSEMBLY

Hide 04495 12.REMOVE REAR BRAKE SHOE KIT (for TMC Made)

Hide 04495 13.REMOVE REAR BRAKE SHOE KIT (for TMMF, TMMCZ Made)

Hide 51447D 14.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 51447D 15.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF, TMMCZ Made)

Hide 57543C 16.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF, TMMCZ Made)

Hide 17410 17.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)

Hide 17410 18.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for M15A-FKS)

Hide 17410 19.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for M15A-FXE)

Hide 58166A 20.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165C 21.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 57628E 22.REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

Hide 57627G 23.REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 58151 24.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR (for TMMF, TMMCZ Made)

Hide 58153 25.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)

Hide 58153 26.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF, TMMCZ Made)

Hide 77606 27.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Gasoline Model)

Hide 77606 28.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for HV Model)

Hide 46430 29.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model TMC Made)

a.

Remove the 4 bolts, nut and No. 3 parking brake cable assembly.

C430747


Hide 46430 30.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for HV Model TMC Made)

a.

Remove the 4 bolts, nut and No. 3 parking brake cable assembly.

C430749


Hide 46430 31.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for TMMF, TMMCZ Made)

a.

Disengage the claw to separate the No. 3 parking brake cable assembly.

C438006


b.

Remove the 3 bolts, nut and No. 3 parking brake cable assembly.


Hide 46420 32.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model TMC Made)

a.

Remove the 5 bolts, nut and No. 2 parking brake cable assembly.

C430751


Hide 46420 33.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for HV Model TMC Made)

a.

Remove the 5 bolts, nut and No. 2 parking brake cable assembly.

C430753


Hide 46420 34.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for TMMF, TMMCZ Made)

a.

Disengage the claw to separate the No. 2 parking brake cable assembly.

C438007


b.

Remove the 4 bolts, nut and No. 2 parking brake cable assembly.