Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Neutral Position Switch Circuit  


DESCRIPTION

The engine stop and start ECU uses the park/neutral position switch assembly installed to the continuously variable transaxle assembly to detect when the shift lever is in P or N.

WIRING DIAGRAM

·
·

for Manual Transaxle:

Refer to DTC P085011.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P085011


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for CVT:

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for CVT A
for Manual Transaxle B



A

2.READ VALUE USING GTS (NEUTRAL SWITCH)

B

5.READ VALUE USING GTS (NEUTRAL SWITCH)
2.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

b.

In accordance with the display on the GTS, read the Data List.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - D45-5 (L) Always Below 1 Ω
A67-17 (CLL) - D45-4 (B) Always Below 1 Ω
A67-21 (STA) - Body ground Always 80 to 180 Ω
A67-17 (CLL) - Body ground Always 10 kΩ or higher
D45-5 (L) - Body ground Always 80 to 180 Ω
D45-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 392 202

b.

Read the value when the shift lever is in neutral and any other position.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever is in neutral ON
Shift lever is in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the D44 neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-26 (TMVC) - D44-1 (W1) Always Below 1 Ω
A67-25 (TME2) - D44-3 (F+) Always Below 1 Ω
A67-8 (TMN) - D44-2 (TMN) Always Below 1 Ω
A67-26 (TMVC) - Body ground and other terminals Always 10 kΩ or higher
D44-1 (W1) - Body ground and other terminals Always 10 kΩ or higher
A67-25 (TME2) - Body ground and other terminals Always 10 kΩ or higher
D44-3 (F+) - Body ground and other terminals Always 10 kΩ or higher
A67-8 (TMN) - Body ground and other terminals Always 10 kΩ or higher
D44-2 (TMN) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A456121C41
3.26,0.094 3.646,0.365 0.385,0.271 3.063,0.948 3.75,1.458 true 3.073,0.833 2.75,1.49 true 0.708,0.094 1.021,0.292 0.313,0.198 10 false *a 3.74,1.5 4.354,1.698 0.615,0.198 10 false TME2 2.646,1.5 3.26,1.698 0.615,0.198 10 false TMN 3.323,0.135 3.938,0.333 0.615,0.198 10 false A67
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-8 (TMN) - A67-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Result Proceed to
OK A
NG B



A

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B