2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSPECTION

Inspection · Vehicles built from Jan 2006


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    Destination
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    General
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    Australia
    175/65R14 82T
    185/60R15 84H
    Driving below 140 km/h (87 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 140 km/h (87 mph)
    260 (2.7, 38)
    260 (2.7, 38)
    G.C.C. Countries
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)

  1. R003031E01
    Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less


ROTATE TIRES

C128523E01

HINT:
Rotate the tires, as shown in the illustration.


INSPECT WHEEL BALANCE

C080976E01
  1. Check and perform off-car balancing.

  1. If required, perform on-car balancing.

    Imbalance after adjustment:
    8 g (0.018 lb) or less


INSPECT FRONT AXLE HUB BEARING
  1. Remove the front wheel.

  1. Separate the disc brake caliper (Click here).

  1. Remove the front disc (Click here).

  1. C107912
    Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the bearing.

  1. C107911
    Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout exceeds the maximum, replace the bearing and axle hub.

  1. Install the front disc (Click here).

  1. Install the disc brake caliper (Click here).

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. Remove the rear brake drum (Click here).

  1. C121815
    Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.

  1. C121816
    Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. Install the rear brake drum.

  1. Adjust the rear drum brake shoe clearance (Click here).

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (from Nov 2005)INSPECTION (from Nov 2006) →