2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSPECTION

Inspection · Vehicles built from Nov 2006


INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    205/45R17 84W
    Driving below 190 km/h (118 mph)
    200 (2.0, 29)
    190 (1.9, 28)
    Driving over 190 km/h (118 mph)
    220 (2.2, 32)
    210 (2.1, 30)

  1. R003031E01
    Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less


ROTATE TIRES

C155588E01

HINT:
Rotate the tires, as shown in the illustration.


INSPECT WHEEL BALANCE

C080976E01
  1. Check and perform off-car balancing.

  1. If required, perform on-car balancing.

    Imbalance after adjustment:
    8 g (0.018 lb) or less


INSPECT FRONT AXLE HUB BEARING
  1. Remove the front wheel.

  1. Separate the disc brake caliper (Click here).

  1. Remove the front disc (Click here).

  1. C107912
    Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the bearing.

  1. C107911
    Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout exceeds the maximum, replace the bearing and axle hub.

  1. Install the front disc (Click here).

  1. Install the disc brake caliper (Click here).

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. for Rear Drum Brake:

    1. Remove the rear brake drum (Click here).

  1. for Rear Disc Brake:

    1. Disconnect the parking brake cable (Click here).

    2. Separate the disc brake cylinder (Click here).

    3. Remove the disc brake pad.

    4. Remove the disc brake cylinder mounting (Click here).

    5. Remove the rear disc (Click here).

  1. C118256E01
    Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.

  1. C118257E01
    Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. for Rear Drum Brake:

    1. Install the rear brake drum.

    2. Adjust the rear drum brake shoe clearance (Click here).

  1. for Rear Disc Brake:

    1. Install the rear disc (Click here).

    2. Install the disc brake cylinder mounting (Click here).

    3. Install the disc brake pad.

    4. Install the disc brake cylinder (Click here).

    5. Connect the parking brake cable (Click here).

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSPECTION (from Jan 2006)INSPECTION (from Aug 2005) →