2005-2008 Yaris · Service Manual ENGINE

P0501 Vehicle Speed Sensor Range / Performance

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.
A079413E13
DTC No.
DTC Detection Condition
Trouble Area
P0501
While vehicle is driven, no vehicle speed sensor signal to ECM (3 trip detection logic)
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM

HINT:
DTC P0501 is detected when the vehicle continues to decelerate for more than 3 seconds after driving at an engine speed of 3,000 rpm or more.


WIRING DIAGRAM

A112582E07

INSPECTION PROCEDURE

NOTICE:
Perform electronic throttle learning after replacing the ECM (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in speedometer malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER
OK


2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Read the value displayed on the tester.

    OK:
    The vehicle speeds displayed on the tester and the speedometer display are equal.



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
A115679E01
  1. Disconnect the combination meter connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground.

    Standard voltage:
    Tester Connection
    Specified Condition
    +S (D1-16) - Body ground
    9 to 14 V

  1. Reconnect the combination meter connector.



NG
Go to step 5
OK


4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A115680E01
  1. Shift the transmission gear selector lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard voltage:
    Tester Connection
    Specified Condition
    +S (D1-16) - Body ground
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
A120352E01
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    +S (D1-16) - SPD (A32-37)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    +S (D1-16) or SPD (A32-37) - Body ground
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0443 Evaporative Emission Control System Purge Control Valve Circuit Malfunction (from Aug 2005)P0561 System Voltage Unstable (from Aug 2005) →