P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
Diagnostic trouble codes · Vehicles built from Nov 2006
Also covers:
- P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
DESCRIPTION
In the VVT system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.| DTC No. |
Detection Condition |
Trouble Area |
| P0016 |
Deviation in crankshaft position sensor signal and camshaft position sensor (for intake camshaft) signal (2 trip detection logic) |
|
| P0017 |
Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic) |
|
- To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0016.
- To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0017.
WIRING DIAGRAM
Refer to DTC P0010 (Click here).Refer to DTC P0013 (Click here).
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 AND P0017) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Result
Proceed to
P0016 or P0017
A
P0016 or P0017 and other DTCs
B
- HINT:
- If any DTCs other than P0016 or P0017 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect an intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
Select the following monitor items: VVT Change Angle (Bank1) and VVT OCV Duty (Bank1).
Check that the VVT Change Angle (Bank1) varies when operating the OCV (for intake camshaft) using the tester.
- OK:
- The VVT Change Angle (Bank1) value and engine speed vary.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).
Select the following monitor items: VVT Ex Change Angle (Bank1) and VVT Ex OCV Duty (Bank1).
Check that the VVT Ex Change Angle (Bank1) value varies when operating the OCV (for exhaust camshaft) using the tester.
- OK:
- The VVT Ex Change Angle (Bank1) value and engine speed vary.
- HINT:
- If the VVT system can be operated through the ACTIVE TEST, it can be assumed that the VVT system is operating normally.
|
|
||||
| OK | |
| 3. ADJUST VALVE TIMING |
![]() ![]() |
- HINT:
- There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match up the timing marks (Click here).
|
|
||||
| 4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) |
- HINT:
- Inspect the specified OCV (OCV for intake camshaft or OCV for exhaust camshaft) in accordance with the inspection result of step 2.
Remove the OCV (for intake camshaft) or OCV (for exhaust camshaft).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω
Apply battery voltage to terminals of the OCV (for intake camshaft) or OCV (for exhaust camshaft). Check the valve operation.

- OK:
- Valve moves quickly.
Reinstall the OCV (for intake camshaft) or OCV (for exhaust camshaft).
|
|
||||
| OK | |
| 5. INSPECT OIL CONTROL VALVE FILTER |
Remove the OCV filter.

Check that the filter is not clogged.
- OK:
- Filter is not clogged.
Reinstall the OCV filter.
|
|
||||
| OK | |
| 6. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
- HINT:
- Replace the specified camshaft timing gear (camshaft timing gear for intake camshaft or exhaust camshaft) in accordance with the inspection result of step 2.
Replace the camshaft timing gear assembly (camshaft timing gear for intake camshaft or exhaust camshaft) (Click here).
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
In order to erase the ECM's learned values for valve timing, disconnect the cable from the negative (-) battery terminal for 1 minute.
Reconnect the cable to the negative (-) battery terminal.
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
Clear DTCs.
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Allow the engine to idle for 5 minutes or more.
Drive the vehicle with a city drive pattern for more than 10 minutes.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Result
Proceed to
No output
A
P0016 or P0017
B
|
|
||||
| A | ||
| ||

