2005-2008 Yaris · Service Manual ENGINE

P0171 System Too Lean (Bank 1)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short- term fuel trim compensation.
If both the short-term and long-term fuel trims are lean or rich beyond predetermined values, it is interpreted as a malfunction, and the ECM illuminates the MIL and sets a DTC.
DTC No.
DTC Detection Conditions
Trouble Areas
P0171
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic)
  1. Air induction system
  2. Fuel injector blockage
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (sensor 1) circuit
  8. Air fuel ratio sensor (sensor 1)
  9. PCV valve and hose
  10. PCV hose connections
  11. ECM
P0172
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic)
  1. Fuel injector leak or blockage
  2. Mass air flow meter
  3. Engine coolant temperature sensor
  4. Ignition system
  5. Fuel pressure
  6. Gas leak from exhaust system
  7. Open or short in air fuel ratio sensor (sensor 1) circuit
  8. Air fuel ratio sensor (sensor 1)
  9. ECM

HINT:
  1. When DTC P0171 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 is set, the actual air-fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be set. The MIL is then illuminated.
  3. When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.


MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air- fuel ratio). If the average fuel trim learning value exceeds the malfunction thresholds, the ECM interprets this a fault in the fuel system and sets a DTC.
Example:
The average fuel trim learning value is more than +35 % or less than -35 %, the ECM interprets this as a fuel system malfunction.
A121607E11

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P0171 or P0172
    A
    P0171 or P0172, and other DTCs
    B

    HINT:
    If any DTCs other than P0171 and P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. CHECK PCV HOSE CONNECTIONS

OK:
PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak.

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS B1S1 and O2S B1S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


    Standard:
    Tester Display
    (Sensor)
    Injection Volumes
    Status
    Voltages
    AFS B1S1
    (A/F)
    +25 %
    Rich
    Less than 3.0 V
    AFS B1S1
    (A/F)
    -12.5 %
    Lean
    More than 3.35 V
    O2S B1S2
    (HO2)
    +25 %
    Rich
    More than 0.55 V
    O2S B1S2
    (HO2)
    -12.5 %
    Lean
    Less than 0.4 V

    Result: 
    Status
    AFS B1S1
    Status
    O2S B1S2
    A/F Condition and
    A/F Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    C
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Fuel injector blockage
    4. Gas leak from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass air flow meter
    8. Engine coolant temperature sensor
    A
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Fuel injector leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. Mass air flow meter
    6. Engine coolant temperature sensor
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean: During Active Test, the air fuel ratio sensor output voltage (AFS) is consistently more than 3.35 V, and the heated oxygen sensor output voltage (O2S) is consistently less than 0.4 V.Rich: During Active Test, the AFS is consistently less than 3.0 V, and the O2S is consistently more than 0.55 V.Lean/Rich: During Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternates correctly.



B
Go to step 11

C
Go to step 14
A


5. READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: 80°C to 100°C (176°C to 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


6. INSPECT MASS AIR FLOW METER
  1. Read values using an intelligent tester (MAF).

    NOTICE:
    1. Turn the ignition switch off.
    2. Perform the inspection with the vehicle indoors and on a level surface.
    3. Perform the inspection of the mass air flow meter while it is installed in the air cleaner case (installed on the vehicle).
    4. During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.

    1. Turn the ignition switch on (IG) (do not start the engine).

    2. Turn the tester on.

    3. Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.

    4. Wait for 30 seconds, and read the values on the intelligent tester.

      Standard:
      Less than 0.19 g/sec

  1. Inspect the mass air flow meter.

    1. Remove the mass air flow meter (Click here).

    2. A154164E01
      Using a work light, check that the platinum filament (heater portion) in the mass air flow meter has no foreign matter attached.

      Standard:
      No foreign matter attached.

    3. Reinstall the mass air flow meter.



NG
REPLACE MASS AIR FLOW METER
OK


7. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8. CHECK EXHAUST GAS LEAK

OK:
No gas leak.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9. CHECK SPARK AND IGNITION

HINT:
  1. Refer to the ignition system inspection procedure (Click here).
  2. If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using an intelligent tester. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count - Cylinder #4 Misfire Count.



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10. INSPECT FUEL INJECTOR (INJECTION AND VOLUME)

HINT:
  1. Refer to the fuel injector inspection procedure (Click here).
  2. If the fuel injectors malfunction, engine misfire may occur. The misfire count can be read using an intelligent tester. Select the following menu items: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count - Cylinder #4 Misfire Count.



NG
REPLACE FUEL INJECTOR
OK


11. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A085152E85
    Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 3 (A1A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


12. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

  1. A112605E07
    Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (HA1A) - C20-109 (HT1A)
    Always
    Below 1 Ω
    C73-3 (A1A+) - C20-112 (A1A+)
    Always
    Below 1 Ω
    C73-4 (A1A-) - C20-113 (A1A-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (HA1A) or C20-109 (HT1A) - Body ground
    Always
    10 kΩ or higher
    C73-3 (A1A+) or C20-112 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C73-4 (A1A-) or C20-113 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.A140695E07



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


14. PERFORM CONFIRMATION DRIVING PATTERN

  1. A115372E95
  2. (a) Connect an intelligent tester to the DLC3.
  3. (b) Turn the ignition switch on (IG).
  4. (c) Turn the tester on.
  5. (d) Clear DTCs (Click here).
  6. (e) Switch the ECM from normal mode to check mode using the tester (Click here).
  7. (f) Start the engine and warm it up with all the accessories switched off.
  8. (g) Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1,400 rpm and 3,200 rpm for 3 to 5 minutes.

    HINT:
    If the system is still malfunctioning, the MIL will be illuminated during step (g).

    NOTICE:
    If the conditions in this test are not strictly followed, no malfunction will be detected.


NEXT


15. CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

Result:
Result
Proceed to
No output
A
P0171 or P0172
B



B
REPLACE ECM
A

END


← P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) (+ P0137, P0138) (from Nov 2006)P0300 Random / Multiple Cylinder Misfire Detected (+ P0301, P0302, P0303, P0304) (from Nov 2006) →