2005-2008 Yaris · Service Manual ENGINE

P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Nov 2006

Also covers:

DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three way catalyst converter and located near the engine assembly.

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor is of the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three way catalytic converter is used in order to convert the carbon monoxide, hydrocarbons, and nitrogen oxide into less harmful substances. To allow the three way catalyst converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio.
*: Value changes inside the ECM. Since the air fuel ratio sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.
A107164E23
DTC No.
DTC Detection Condition
Trouble Area
P2195
Conditions (a) and (b) continue for 10 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage more than 3.8 V
(b) Heated oxygen sensor voltage 0.15 V or more
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. Air fuel ratio sensor heater (sensor 1)
  4. Integration relay (EFI relay)
  5. Air fuel ratio sensor heater circuit
  6. ECM
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current 3.6 mA or more for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor (Sensor 1)
  2. ECM
P2196
Conditions (a) and (b) continue for 10 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage less than 2.8 V for 10 seconds
(b) Heated oxygen sensor voltage less than 0.6 V
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. Air fuel ratio sensor heater (sensor 1)
  4. Integration relay (EFI relay)
  5. Air fuel ratio sensor heater circuit
  6. ECM
While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current less than 1.57 mA for 3 seconds (2 trip detection logic)
  1. Air fuel ratio sensor (Sensor 1)
  2. ECM

HINT:
  1. When either of these DTCs is set, check the air fuel ratio sensor output voltage by selecting the following menu items on an intelligent tester: Powertrain / Engine and ECT / Data List / AFS B1 S1.
  2. Short-term fuel trim values can also be read using the intelligent tester.
  3. The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the intelligent tester.
  4. If the air fuel ratio sensor is malfunctioning, the ECM sets the DTC P2195 or P2196.


WIRING DIAGRAM

A159159E01

CONFIRMATION DRIVING PATTERN


  1. This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

    A107162E33

    A107163E21
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG).
    3. Turn the tester on.
    4. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
    5. Clear DTCs.
    6. Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher (Procedure "A").
    7. On the intelligent tester, select the following menu items to check the fuel-cut status: Powertrain / Engine and ECT / Data List / All Data / Idle Fuel Cut.
    8. Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes (Procedure "B").
    9. Change the transmission to the 2nd gear (Procedure "C").
    10. Drive the vehicle at a proper vehicle speed to perform fuel-cut operation (Procedure "D") (refer to the following HINT).

      HINT:
      Fuel-cut is performed when the following conditions are met:
      1. Accelerator pedal fully released.
      2. Engine speed is 2,500 rpm or more (fuel injection resumes at 1,000 rpm).

    11. Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds (Procedure "E").
    12. Soon after performing Procedure "E" above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control (Procedure "F").
    13. Allow the vehicle to decelerate until the vehicle speed declines to less than 10 km/h (6 mph).
    14. Repeat steps from Procedure "C" through Procedure "F" above at least 3 times in one driving cycle (Procedure "G").
    15. Turn the ignition switch off.
    16. Repeat steps from Procedure "A" through Procedure "G" again.

      CAUTION:
      Strictly observe posted speed limits, traffic laws, and road conditions when performing these driving patterns.


INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
  6. Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1 S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1 S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1 S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1 S2
(HO2)
-12.5%
Lean
Less than 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E01
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E01
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Fuel injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2.

HINT:
  1. DTC P2A00 may be set when the air fuel ratio is stuck rich or lean.
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  4. A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P2195 or P2196
    A
    P2195 or P2196 and other DTCs
    B

HINT:
If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.

  1. Clear DTCs.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / AFS B1 S1.

  1. Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Monitor Driving Pattern 2 (Detail for Procedure "C" through Procedure "G") in the CONFIRMATION DRIVING PATTERN.

    HINT:
    1. To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.
    2. If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the intelligent tester.


Result:
Result
Proceed to
Within normal range (1.57 mA or more, and less than 3.6 mA)
A
Outside normal range (Less than 1.57 mA, or 3.6 mA or more)
B



B
Go to step 21
A


3. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Warm up the air fuel ratio sensor at an engine speed of 2,500 rpm for 90 seconds.

  1. On the tester, select the following menu items: Powertrain / Engine and ECT / Data List / AFS B1 S1 and Engine Speed / Function / Snap Shot Record.

  1. Check the air fuel ratio sensor voltage 3 times, when the engine is in each of the following conditions:

    1. While idling (for at least 30 seconds) (Step "A").

    2. At an engine speed of approximately 2,500 rpm (without any sudden changes in engine speed) (Step "B").

    3. Raise the engine speed to 4,000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed (Step "C").

      Standard voltage:
      Condition
      A/F Sensor Voltage Variation
      Reference
      Step "A" and Step "B"
      Remains at approximately 3.3 V
      Between 3.1 V and 3.5 V
      Step "C"
      Increases to 3.8 V or more
      This occurs during engine deceleration
      (when fuel-cut performed)

HINT:

  1. For more information, see the diagrams below.

    A107161E22
  2. If the output voltage of the air fuel ratio sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the air fuel ratio sensor may have an open circuit. (This will also happen if the air fuel ratio sensor heater has an open circuit.)
  3. If the output voltage of the air fuel ratio sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those above, the air fuel ratio sensor may have a short circuit.
  4. The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the air fuel ratio sensor output voltage.
  5. The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.
  6. When the vehicle is driven:
    The output voltage of the air fuel ratio sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The air fuel ratio F sensor is functioning normally.
  7. The air fuel ratio sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the air fuel ratio sensor or ECM will show a constant voltage result.



NG
Go to step 10
OK


4. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P2195 or P2196
    A
    No output
    B



B
Go to step 9
A


6. REPLACE AIR FUEL RATIO SENSOR

NEXT


7. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P2195 or P2196
    B



B
REPLACE ECM
A


9. CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST


NO
CHECK FOR INTERMITTENT PROBLEMS (Click here)
YES

DTC CAUSED BY RUNNING OUT OF FUEL

10. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. A085152E85
    Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 3 (A1A-)
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


11. INSPECT AIR FUEL RATIO SENSOR (POWER SOURCE)

  1. A079114E18
    Disconnect the air fuel ratio sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C73-2 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 20
OK


12. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

  1. A112605E07
    Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (HA1A) - C20-109 (HT1A)
    Always
    Below 1 Ω
    C73-3 (A1A+) - C20-112 (A1A+)
    Always
    Below 1 Ω
    C73-4 (A1A-) - C20-113 (A1A-)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C73-1 (HA1A) or C20-109 (HT1A) - Body ground
    Always
    10 kΩ or higher
    C73-3 (A1A+) or C20-112 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C73-4 (A1A-) or C20-113 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.A140695E07



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leak.

    OK:
    No leak from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


14. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


15. INSPECT FUEL INJECTOR
  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR
OK


16. REPLACE AIR FUEL RATIO SENSOR

NEXT


17. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


18. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P2195 or P2196
    B



B
REPLACE ECM
A


19. CONFIRM WHETHER VEHICLE RUN OUT OF FUEL IN PAST


NO
CHECK FOR INTERMITTENT PROBLEMS (Click here)
YES

DTC CAUSED BY RUNNING OUT OF FUEL

20. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY)

  1. A112603E02
    Disconnect the air fuel ratio sensor connector.

  1. Remove the integration relay from the engine room R/B and J/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    C73-2 (+B) - 1A-4
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    C73-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)

21. REPLACE AIR FUEL RATIO SENSOR

NEXT


22. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


23. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    No output
    A
    P2195 or P2196
    B



B
REPLACE ECM
A

END


← P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance (from Nov 2006)P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ P2238, P2239, P2252, P2253) (from Nov 2006) →