2005-2008 Yaris · Service Manual TRANSMISSION

P0920 Gear Shift Forward Actuator Circuit

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

C112283E04
The shift and select actuator is operated by the transmission control ECU and changes the transmission gear by the shift and select lever shaft movement. An electric motor (shift motor) moves the shift and select lever shaft in the shift direction, and the shift stroke sensor, which is mounted on the shift and select actuator assembly, detects the shift position. The transmission control ECU monitors the electrical current and shift motor output terminal voltage, and detects malfunctions in the shift motor circuit.
DTC No.
DTC Detection Conditions
Trouble Areas
P0920
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Shift motor is not energized
  2. Shift motor voltage is less than 0.5 V*1, or more than threshold*2 for 0.5 seconds
  3. +BM voltage is 10 V or more
  1. Shift and select actuator assembly (shift motor)
  2. Short in shift motor circuit
  3. Transmission control ECU
P0920
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Shift motor is energized
  2. Target shift motor current is more than 5A
  3. Actual shift motor current is less than 1A*3
  1. Shift and select actuator assembly (shift motor)
  2. Open in shift motor circuit
  3. Transmission control ECU
P0920
The transmission control ECU detects the following conditions:
(1 trip detection logic)
  1. Shift motor is not energized
  2. Difference between maximum and minimum voltages of shift motor terminal (MSF+ or MSF-) is more than threshold*4 for 0.5 seconds
  3. +BM voltage is 10 V or more
  1. Shift and select actuator assembly (shift motor)
  2. Open in shift motor circuit
  3. Transmission control ECU
  1. *1: A short between the shift motor circuit and the body ground is suspected.
  2. *2: A short between the shift motor circuit and the +B circuit is suspected.
  3. *3: An open in the shift motor circuit is suspected. When the motor current does not flow to the ECU terminals despite the ECU ordering the shift motor to operate, the ECU sets the DTC.
  4. *4: An open in the shift motor circuit is suspected. When the difference exceeds the threshold despite the ECU not ordering the shift motor to operate, the ECU sets the DTC.

WIRING DIAGRAM

C111577E03

INSPECTION PROCEDURE

NOTICE:
  1. In clutch actuator assembly replacement, perform Clamp Position Adjustment before removing the actuator (Click here).
  2. In shift stroke sensor or shift and select actuator assembly replacement, perform the [Initialization and Learning] procedure (Click here) and [Synchronization Position Calibration] procedure (Click here) after installing the sensor or actuator assembly. If the sensor or actuator is installed without performing [Initialization and Learning] and [Synchronization Position Calibration], it may cause driving performance degradation or system component breakage.


1. INSPECT SHIFT AND SELECT ACTUATOR ASSEMBLY
C112279E01
  1. Disconnect the shift motor connector.

  1. Measure the shift motor resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    0.1 to 100 Ω

  1. Reconnect the shift motor connector.



NG
REPLACE SHIFT AND SELECT ACTUATOR ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (SHIFT AND SELECT ACTUATOR - TRANSMISSION CONTROL ECU)
C113924E08
  1. Disconnect the shift motor connector.

  1. Disconnect the transmission control ECU connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    MSF- (A37-3) - (A46-1)
    Below 1 Ω
    MSF+ (A37-1) - (A46-2)
    Below 1 Ω
    MSF- (A37-3) - Body ground
    10 kΩ or higher
    MSF+ (A37-1) - Body ground
    10 kΩ or higher

  1. Reconnect the shift motor connector.

  1. Reconnect the transmission control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY


← P0919 Gear Shift Position Control Error (from Nov 2005)P1875 Buzzer Malfunction (from Nov 2005) →