2005-2008 Yaris · Service Manual TRANSMISSION

U0100 Lost Communication with ECM / PCM "A"

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

The transmission control ECU and ECM communicate with each other via the CAN communication line. The transmission control ECU also communicates with the other computers through the ECM.
DTC No.
DTC Detection Conditions
Trouble Areas
U0100
No communication with the ECM
(1 trip detection logic)
  1. Open or short in CAN signal circuit
  2. ECM
  3. Transmission control ECU

WIRING DIAGRAM

C127411E01

INSPECTION PROCEDURE

HINT:
  1. Refer to inspection procedure for CAN communication system (Click here).
  2. If the CAN communication malfunctions, the transmission control ECU cannot receive the current data from the ECM. In this case, the freeze frame data output from the transmission control ECU have not been updated so the data will not be useful for the inspection. However, reading the Data List as the first step of troubleshooting is effective to find malfunctions.
  3. The malfunction area can be checked using the BUS CHECK function on the intelligent tester (Click here).
  4. There are two types of engine for multi-mode manual transmission system in this vehicle. One is 2SZ-FE model, and other is 1KR-FE model.
    For details of the 2SZ-FE ECM terminals, refer to TERMINALS OF ECM (Click here).
    For details of the 1KR-FE ECM terminals, refer to TERMINALS OF ECM (Click here).

NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these reference values when deciding whether a part is faulty or not.

To check the Data List, perform the following procedure using the intelligent tester.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch on (IG) and turn the tester ON.
  5. Following the display on the tester, read the Data List.
Items
[Abbreviation]
Measurement Items: Display
Normal Conditions
Diagnostic Notes
Calculated Engine Load
[Calc E/G Load]
Calculated load by ECM:
Min.: 0 %, Max.: 100 %
1KR-FE:
11 to 25 %: Idling
15 to 35 %: Running without load (2,500 rpm)
2SZ-FE:
10 to 30 %: Idling
10 to 30 %: Running without load (2,500 rpm)
-
Engine Coolant Temperature
[Coolant Temp]
Coolant temperature:
Min.: -40°C , Max.: 215°C
1KR-FE:
75 to 95°C (167 to 203°F):
After engine warmed up
2SZ-FE:
80 to 100°C (176 to 212°F):
After engine warmed up
  1. If value -40°C (-40°F): sensor circuit open
  2. If value 140°C (284°F): sensor circuit shorted
Backup Engine Speed
[Bacup Engin Spd]
Back-up engine speed:
Min.: 0 rpm, Max.: 8,160 rpm
0 rpm: Engine stopped
Approximately same as tachometer reading: Engine running
0 rpm displayed when CAN communication malfunctions
Accelerator Pedal Angle
[Accel Pedl Angl]
Accelerator pedal angle
Min.: 0 %, Max.: 100 %
0 to 25 %: Accelerator pedal released
52 to 100 %: Accelerator pedal depressed
0 % displayed when CAN communication malfunctions

NOTICE:
Only for 1KR-FE:
In ECM replacement, perform the electronic throttle learning after installing the ECM (Click here).


← P1875 Buzzer Malfunction (from Nov 2005)Starter Signal Circuit (from Nov 2005) →