P0812 Reverse Input Circuit
Diagnostic trouble codes · Vehicles built from Nov 2005
DESCRIPTION
As one judgment method, the transmission control ECU uses the back up light switch signal indicating whether the gear is in reverse or not. Receiving the signals from the back up light switch assembly and the shift and select stroke sensors, the transmission control ECU detects that the transmission gear is in reverse. If the signal from the back up light switch assembly does not match the signals from the shift and select stroke sensors, the transmission control ECU sets the DTC.| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0812 |
The transmission control ECU detects the following conditions simultaneously: (1 trip detection logic)
|
|
| P0812 |
The transmission control ECU detects the following conditions simultaneously: (1 trip detection logic)
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- In shift and select stroke sensors replacement, perform [Initialization and Learning] and [Synchronization Position Calibration] after installing the sensors (Click here).
- If the sensors are installed without performing [Initialization and Learning] and [Synchronization Position Calibration], it may cause driving performance degradation or system component breakage.
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and the tester ON.
Select the following menu items: Powertrain / Multi-Mode M/T / Data List / T/M Reverse Switch Signal and Gear Position (Current).
Items
[Abbreviation]
Measurement Items: Display
Normal Conditions
Diagnostic Notes
T/M Reverse Switch Signal
[T/M R SW Sig]
Transmission reverse switch signal:
OFF or ON
ON: Transmission gear in reverse
OFF: Other than above
During malfunctions, indicator shows either ON or OFF continuously, regardless of gear position
Gear Position (Current)
[Gear Pos-Cur]
Current gear position:
Min.: 0, Max.: 7
Actual gear position displayed
0 = Neutral
1 to 6 = 1th to 6th
7 = Reverse
- OK:
- When the shift lever is operated, the normal condition listed above is shown on the tester.
|
|
||||
| NG | |
| 2. INSPECT BACK UP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the back up light switch assembly.
Check the resistance when the switch condition is released and pushed.
- Standard resistance:
Tester Connections
Switch Conditions
Specified Conditions
1-2
Released
10 kΩ or higher
1-2
Pushed
Below 1 Ω
Reinstall the back up light switch assembly.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (BACK UP LIGHT SWITCH - TRANSMISSION CONTROL ECU) |
![]() ![]() |
Disconnect the back up light switch assembly connector.
Disconnect the transmission control ECU connector.
Remove the back up light bulbs.
Check the resistance.
- Standard resistance:
Tester Connections
Specified Conditions
RSW (A38-9) - (A50-1)
Below 1 Ω
RSW (A38-9) - Body ground
10 kΩ or higher
Turn the ignition switch on (IG).
Measure the voltage between the terminal of the back up light switch assembly and the body ground.
- Standard voltage:
Tester Connections
Specified Conditions
(A50-2) - Body ground
10 to 14 V
Reconnect the back up light switch assembly connector.
Reconnect the transmission control ECU connector.
Reinstall the back up light bulbs.
|
|
||||
| OK | |
| 4. INSPECT SHIFT STROKE SENSOR |
![]() ![]() |
Remove the shift stroke sensor.
Measure the voltage between the terminals of the shift stroke sensor connector (main).
Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.
Connect the batteries in series.
Connect the positive battery terminal to sensor terminal 3, and the negative battery terminal to sensor terminal 2.
Check the voltage between terminals 1 and 2.
- Standard voltage (combined dry cell battery voltage of 4.5 V):
Sensor Angle
Terminal (1-2) Output Voltage
55°
Approximately 4.05 V
0°
Approximately 2.25 V
-55°
Approximately 0.45 V
- Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
Sensor Angle
Terminal (1-2) Output Voltage
55°
Approximately 4.5 V
0°
Approximately 2.5 V
-55°
Approximately 0.5 V
Measure the voltage between the terminals of the shift stroke sensor connector (sub).

Connect the positive battery terminal to sensor terminal 6, and the negative battery terminal to sensor terminal 5.
Check the voltage between terminals 4 and 5.
- Standard voltage (combined dry cell battery voltage of 4.5 V):
Sensor Angle
Terminal (4-5) Output Voltage
55°
Approximately 4.05 V
0°
Approximately 2.25 V
-55°
Approximately 0.45 V
- Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
Sensor Angle
Terminal (4-5) Output Voltage
55°
Approximately 4.5 V
0°
Approximately 2.5 V
-55°
Approximately 0.5 V
- NOTICE:
- Do not apply more than 6 V
- Do not use a sensor which has been dropped.
- Do not apply more than 6 V
Reinstall the shift stroke sensor (Click here).
Perform [Initialization and Learning] (Click here) and [Synchronization Position Calibration] (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SHIFT STROKE SENSOR - TRANSMISSION CONTROL ECU) |
![]() ![]() |
Disconnect the shift stroke sensor connector.
Disconnect the transmission control ECU connector.
Check the resistance.
- Standard resistance:
Tester Connections
Specified Conditions
VCS2 (A38-30) - (A44-6)
Below 1 Ω
VSS2 (A38-29) - (A44-4)
Below 1 Ω
E2S2 (A38-28) - (A44-5)
Below 1 Ω
VCS1 (A38-19) - (A44-3)
Below 1 Ω
VSS1 (A38-18) - (A44-1)
Below 1 Ω
E2S1 (A38-17) - (A44-2)
Below 1 Ω
VCS2 (A38-30) - Body ground
10 kΩ or higher
VSS2 (A38-29) - Body ground
10 kΩ or higher
E2S2 (A38-28) - Body ground
10 kΩ or higher
VCS1 (A38-19) - Body ground
10 kΩ or higher
VSS1 (A38-18) - Body ground
10 kΩ or higher
E2S1 (A38-17) - Body ground
10 kΩ or higher
Reconnect the shift stroke sensor connector.
Reconnect the transmission control ECU connector.
|
|
||||
| OK | |
| 6. INSPECT SELECT STROKE SENSOR |
![]() ![]() |
Remove the select stroke sensor.
Measure the voltage between the terminals of the select stroke sensor connector (main).
Prepare 3 dry cell batteries (1.5 V) and 2 leads for connecting the batteries and the sensor.
Connect the batteries in series.
Connect the positive battery terminal to sensor terminal 3, and the negative battery terminal to sensor terminal 2.
Check the voltage between terminals 1 and 2.
- Standard voltage (combined dry cell battery voltage of 4.5 V):
Sensor Angle
Terminal (1-2) Output Voltage
55°
Approximately 4.05 V
0°
Approximately 2.25 V
-55°
Approximately 0.45 V
- Reference Voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
Sensor Angle
Terminal (1-2) Output Voltage
55°
Approximately 4.5 V
0°
Approximately 2.5 V
-55°
Approximately 0.5 V
Measure the voltage between the terminals of the select stroke sensor connector (sub).

Connect the positive battery terminal to sensor terminal 6, and the negative battery terminal to sensor terminal 5.
Check the voltage between terminals 4 and 5.
- Standard voltage (combined dry cell battery voltage of 4.5 V):
Sensor Angle
Terminal (4-5) Output Voltage
55°
Approximately 4.05 V
0°
Approximately 2.25 V
-55°
Approximately 0.45 V
- Reference voltage (combined dry cell battery voltage of 5.0 +- 0.3 V):
Sensor Angle
Terminal (4-5) Output Voltage
55°
Approximately 4.5 V
0°
Approximately 2.5 V
-55°
Approximately 0.5 V
- NOTICE:
- Do not apply more than 6 V
- Do not use a sensor which has been dropped.
- Do not apply more than 6 V
Reinstall the select stroke sensor (Click here).
Perform [Initialization and Learning] (Click here) and [Synchronization Position Calibration] (Click here).
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (SELECT STROKE SENSOR - TRANSMISSION CONTROL ECU) |
![]() ![]() |
Disconnect the select stroke sensor connector.
Disconnect the transmission control ECU connector.
Check the resistance.
- Standard resistance:
Tester Connections
Specified Conditions
VCL2 (A38-31) - (A45-6)
Below 1 Ω
VSL2 (A38-32) - (A45-4)
Below 1 Ω
E2L2 (A38-24) - (A45-5)
Below 1 Ω
VCL1 (A38-20) - (A45-3)
Below 1 Ω
VSL1 (A38-21) - (A45-1)
Below 1 Ω
E2L1 (A38-22) - (A45-2)
Below 1 Ω
VCL2 (A38-31) - Body ground
10 kΩ or higher
VSL2 (A38-32) - Body ground
10 kΩ or higher
E2L2 (A38-24) - Body ground
10 kΩ or higher
VCL1 (A38-20) - Body ground
10 kΩ or higher
VSL1 (A38-21) - Body ground
10 kΩ or higher
E2L1 (A38-22) - Body ground
10 kΩ or higher
Reconnect the select stroke sensor connector.
Reconnect the transmission control ECU connector.
|
|
||||
| OK | ||
| ||





