2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT ENGINE COOLANT

INSPECT ENGINE OIL

A104283E01
  1. Check engine oil level.

    1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick's low level mark and full level mark.
      If low, check for leakage and add oil up to the full level mark.

      NOTICE:
      Do not fill with engine oil to above the full level mark.

  1. A113813E01
    Check engine oil quality.

    1. Check the oil for deterioration, water contamination, discoloration and thinning.
      If the quality is visibly poor, replace the oil.

      Oil grade:
      20W-50 and 15W-40:
      API grade SL or SM multigrade engine oil
      10W-30 and 5W-30:
      API grade SL "Energy-Conserving" "Energy-Conserving SM or ILSAC multigrade engine oil"


INSPECT BATTERY

INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element from the cylinder head cover sub-assembly.

  1. Visually check that there is no dirt, clogging, /or damage to the air cleaner filter element.

    HINT:
    1. If there is any dirt or a clog on the air cleaner filter element, clean it with compressed air.
    2. If any dirt or a clog remains even after cleaning the air cleaner filter element with compressed air, replace it.


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not attempt to adjust the electrode gap of a used spark plug.

  1. I039522E07
    Check the electron.

    1. Using a megaohmmeter, measure the insulation resistance.

      Standard resistance:
      10 MΩ or more

      If the resistance is less than the specified value, proceed to step (*3).

      HINT:
      If a megaohmmeter is not available, perform the following simple inspection instead.

  1. P003783
    Alternative inspection method:

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. Visually check the spark plug.

    4. If the electron is dry, the spark plug is functioning. Proceed to step 2.

    5. If the electrode is damp, proceed to steps (*1), (*2) and (*3).

    6. Install the spark plug.

  1. Check the spark plug for any damage to its threads and insulator. (*1)
    If there is any damage, replace the spark plug.

    Recommended spark plug:
    Supplier
    Parts code
    DENSO
    K20HR-U11

  1. P003792
    Check the spark plug electrode gap. (*2)

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Correct electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

    NOTICE:
    Bend only the base of the ground electrode when adjusting the gap of a new spark plug.

  1. B062019
    Clean the spark plugs. (*3)
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf/cm2, 85psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.


INSPECT IGNITION TIMING

NOTICE:
  1. Turn all the electrical systems and the A/C off.
  2. Inspect the ignition timing with the cooling fan off.
  3. When checking the ignition timing, shift the transmission to the neutral position.

  1. Warm up and stop the engine.

  1. A117072E02
    When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the Ignition Switch on (IG).

    3. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TE1 (TC) / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further information regarding the selection of Active Test.

    4. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12° BTDC

    5. Select the following menu items:
      TE1 (TC) / OFF

    6. Turn the Ignition Switch off.

    7. Disconnect the intelligent tester from the DLC3.

  1. When not using the intelligent tester:

    1. Remove the air cleaner cap sub-assembly (Click here).

    2. A104119
      Install the tester terminal of a timing light onto the position shown in the illustration.

      NOTICE:
      1. Use a timing light that detects the first signal.
      2. Wrap the wire harness with tape after checking.

    3. A118802E01
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      Check the terminal numbers before connecting them. Connecting the wrong terminals could damage the engine.

    4. Turn the Ignition Switch on (IG).

    5. Inspect the ignition timing during idling.

      Ignition timing:
      0 to 15° BTDC

      HINT:
      Run the engine speed at 1,000 to 1,300 rpm for 5 seconds, then check that the engine speed returns to the idling speed.

    6. Disconnect terminals 13 (TC) and 4 (CG) of the DCL3.

    7. Turn the Ignition Switch off.

    8. Remove the timing light.

    9. Install the air cleaner cap sub-assembly (Click here).


INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems and the A/C off.
  2. Inspect the engine idling speed with the cooling fan off.
  3. When checking the idling speed, shift the transmission to the neutral position.

  1. Warm up and stop the engine.

  1. A117072E02
    When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the Ignition Switch on (IG).

    3. Select the following menu items:
      Powertrain / Engine and ECT / Data List / Engine SPD.

      HINT:
      Refer to the intelligent tester operator's manual for further information regarding the selection of Data List.

    4. Inspect the engine idling speed.

      Idling speed:
      730 to 830 rpm

    5. Turn the Ignition Switch off.

    6. Disconnect the intelligent tester from the DCL3.

  1. A118802E02
    When not using an intelligent tester:

    1. Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.

      SST
      09843-18040  

      NOTICE:
      Check the terminal numbers before connecting them. Connecting the wrong terminals could damage the engine.

    2. Turn the Ignition Switch on (IG).

    3. Inspect the engine idling speed.

      Idling speed:
      730 to 830 rpm

    4. Turn the Ignition Switch off.

    5. Disconnect the tachometer.

    6. Remove SST from terminal 9 (TAC).


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the air cleaner cap sub-assembly (Click here).

  1. Remove the 3 ignition coils (Click here).

  1. Remove the 3 spark plugs.

  1. Disconnect the 3 fuel injector connectors.

  1. A104120
    Inspect the cylinder compression pressure.

    1. Install SST (compression gauge) into the spark plug hole.

      SST
      09992-00500  

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression pressure (Normal condition):
      1,422 kPa (14.5 kgf/cm2, 206 psi)

      Minimum pressure:
      1,079 kPa (11.0 kgf/cm2, 156 psi)

      Difference between each cylinder:
      147 kPa (1.5 kgf/cm2, 21 psi) or less

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 400 rpm or more.
      2. Inspect the other cylinders in the same way.
      3. Measure the compression as quickly as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

      HINT:
      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If the pressure remains low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 3 fuel injector connectors.

  1. Install the 3 spark plugs.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Install the 3 ignition coils (Click here).

  1. Install the air cleaner cap sub-assembly (Click here).


INSPECT CO/HC

HINT:
The ECM controls the concentration of CO/HC in the emission gas.

  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Check the CO/HC concentration during idling and when running at 2,500 rpm.

    Standard:
    CO concentration:
    0.2 % or less
    HC concentration:
    70 ppm or less

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
    1. Check the heated oxygen sensor operation (Click here and/or Click here).
    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
    CO
    HC
    Problems
    Causes
    Normal
    High
    Rough idling
    1. Faulty ignition:
      1. Fouled, shorted or improperly gapped plugs
    2. Incorrect valve clearance
    3. Leakage from intake and exhaust valves
    4. Leakage from cylinders
    Low
    High
    Rough idling
    (Fluctuating HC reading)
    1. Lean mixture causing misfire
    2. Faulty SFI systems:
      1. Faulty pressure regulator
      2. Faulty engine coolant temperature sensor
      3. Faulty mass air flow meter
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle body
    High
    High
    Rough idling
    (Black smoke from exhaust)
    1. Faulty SFI systems:
      1. Faulty pressure regulator
      2. Faulty engine coolant temperature sensor
      3. Faulty mass air flow meter
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle body

← PRECAUTION (from Aug 2005)COMPONENTS (from Aug 2005) →