2005-2008 Yaris · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Nov 2006

HINT:
In this section, the terms Cold and Hot refer to the temperature of the coils. Cold means approximately -10 to 50 °C (14 to 122 °F). Hot means approximately 50 to 100 °C (122 to 212 °F).


INSPECT IGNITION COIL AND SPARK TEST
  1. Check for DTCs.

    NOTICE:
    If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.

  1. Check whether sparks occur.

    1. Remove the No. 2 cylinder head cover (Click here).

    2. Remove the 4 ignition coils (Click here).

    3. Using a 14mm (0.55 in) plug wrench, remove the 4 spark plugs.

    4. Install the spark plug into the ignition coil and connect the ignition coil connector.

    5. Disconnect the 4 injector connectors.

    6. Ground the spark plug.

    7. Check that sparks occur while the engine is being cranked.

      NOTICE:
      1. Ground the spark plug when checking.
      2. Replace the ignition coil when it has been subjected to a physical impact.
      3. Do not crank the engine for more than 2 seconds.
      If sparks do not occur, perform the following procedure.

  1. Perform the spark test in accordance with the following procedure:

    1. Check that the wire harness connector of the ignition coil is securely connected.

      Result:
      Result
      Proceed to
      NG
      Connect securely
      OK
      Go to next step

    2. Perform a spark test on each ignition coil with igniter.

      1. Replace the ignition coil with a functioning one.
      2. Perform the spark test again.

      Result:
      Result
      Proceed to
      OK
      Replace ignition coil with igniter
      NG
      Go to next step

    3. Check the spark plug.

      Result:
      Result
      Proceed to
      NG
      Replace spark plug
      OK
      Go to next step

    4. Check the power supply to each ignition coil with igniter.

      1. Turn the ignition switch on (IG).
      2. Check that there is battery voltage at the positive (+) ignition coil terminal (Click here).

      Result:
      Result
      Proceed to
      NG
      Check wiring between ignition switch and ignition coil with igniter
      OK
      Go to next step

    5. Check the crankshaft position sensor (Click here).

      Result:
      Result
      Proceed to
      NG
      Replace crankshaft position sensor
      OK
      Go to next step

    6. Check the IGT and IGF signal circuits (Click here).

      Result:
      Result
      Proceed to
      NG
      Check ECM
      OK
      Repair wiring between ignition coil and ECM

  1. Connect the 4 injector connectors.

  1. Using a 14 mm (0.55 in) plug wrench, install the 4 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the 4 ignition coils (Click here).

  1. Install the No. 2 cylinder head cover (Click here).


INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.

  1. I039522E11
    Check the electrode.

    1. Using a megaohmmeter, measure the insulation resistance.

      Standard resistance:
      10 MΩ or more

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      1. If a megaohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Quickly accelerate the engine to 4,000 rpm 5 times.

    2. Remove the spark plug.

    3. B001301E01
      Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its thread and insulator.
    If there is damage, replace the spark plug.

    Recommended spark plug:
    Manufacturer
    Product
    DENSO
    SC20HR11

  1. B002101E04
    Check the spark plug electrode gap.

    Maximum electrode gap for used spark plug:
    1.3 mm (0.051 in.)

    If the gap is greater than the maximum, replace the spark plug.

    Electrode gap for new spark plug:
    1.0 to 1.1 mm (0.039 to 0.043 in.)

  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Air pressure:
    588 kPa (6 kgf/cm2, 85 psi)

    Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

← SYSTEM DIAGRAM (from Nov 2006)COMPONENTS (from Nov 2006) →