2005-2008 Yaris · Service Manual ENGINE

P0698 Sensor Reference Voltage "C" Circuit Low

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

Refer to DTC P0190 (Click here) and DTC P0236 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0698
Power voltages (5 V as standard) supplied from ECM to both fuel pressure and manifold pressure sensors are lower than appropriate thresholds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor
  3. Open or short in manifold absolute pressure sensor circuit
  4. Manifold absolute pressure sensor
  5. ECM
P0699
Power voltages (5 V as standard) supplied from ECM to both fuel pressure and manifold pressure sensors are higher than appropriate thresholds
(The MIL is illuminated and a DTC is immediately set when a malfunction is detected)

HINT:
These DTCs are set when the ignition switch is in the on (IG) position.


WIRING DIAGRAM

Refer to DTC P0190 (Click here) and DTC P0236 (Click here).

INSPECTION PROCEDURE


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0698 AND/OR P0699)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0698 and/or P0699
    A
    P0698 and/or P0699 and other DTCs
    B

    HINT:
    If any DTCs other than P0698 and/or P0699 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

  1. A122674E01
    Disconnect the C56 fuel pressure sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    16.4 kΩ or less
    2 - 3
    3 kΩ or less

  1. Reconnect the fuel pressure sensor connector.



NG
REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

  1. A122650E01
    Disconnect the C56 fuel pressure sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    PC (C50-37) - PCR1 (C56-2)
    Below 1 Ω
    VCS (C50-26) - VC1 (C56-3)
    E2S (C50-16) - E1 (C56-1)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    PC (C50-37) or PCR1 (C56-2) - Body ground
    10 kΩ or higher
    VCS (C50-26) or VC1 (C56-3) - Body ground
    E2S (C50-16) or E1 (C56-1) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the fuel pressure sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / PIM.

  1. Read the values displayed on the tester.

    OK:
    Same value as the actual atmospheric pressure.



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK


5. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A122603E01
    Disconnect the A33 manifold absolute pressure sensor connector.

  1. Disconnect the C50 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    PIM (A33-2) - PIM (C50-38)
    Below 1 Ω
    VC (A33-3) - VPIM (C50-30)
    E (A33-1) - EPIM (C50-17)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    PIM (A33-2) or PIM (C50-38) - Body ground
    10 kΩ higher
    VC (A33-3) or VPIM (C50-30) - Body ground
    E (A33-1) or EPIM (C50-17) - Body ground

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0685 ECM / PCM Power Relay Control Circuit / Open (from Nov 2005)P0704 Clutch Switch Input Circuit Malfunction (from Nov 2005) →