Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

DTC    C1413    Front Speed Sensor RH Output Malfunction

DTC    C1414    Front Speed Sensor LH Output Malfunction

for Preparation Click here


DESCRIPTION

Refer to DTCs C1401 and C1402 .

DTC Code
DTC Detection Condition
Trouble Area
C1413
C1414
When any of the following is detected:
  1. Momentary interruption of the sensor signal from the abnormal wheel occurs 255 times or more.
  2. At vehicle speed of 20 km/h (12 mph) or more, noise occurs 75 times or more in sensor signal from a specific wheel for 5 seconds.
  3. At vehicle speed of 10 km/h (6 mph) or more, noise input occurs once per rotor rotation for 15 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Speed sensor rotor
  4. Sensor installation
  5. Brake actuator assembly (Skid control ECU)
C1275
C1276
Detected only during Test Mode.
  1. Front speed sensor RH/LH
  2. Sensor installation
  3. Speed sensor rotor

HINT:
  1. DTCs C1275 and C1276 are output only in the Test Mode.
  2. DTCs C1275 and C1276 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends.
  3. DTCs C1413 and C1275 are for the front speed sensor RH.
  4. DTCs C1414 and C1276 are for the front speed sensor LH.


WIRING DIAGRAM


C149728E20


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using an intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    FR speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    FL Speed Open
    FL speed sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    OK:
    There are no momentary interruptions

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 11
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.CHECK IF SKID CONTROL ECU AND FRONT SPEED SENSOR CONNECTORS ARE SECURELY CONNECTED
  1. Check if the skid control ECU and the front speed sensor connectors are securely connected.


NEXT


4.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


5.CHECK FRONT SPEED SENSOR INSTALLATION


    C144929E15
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation nut is tightened properly.
    Torque:
    10 N*m (105 kgf*cm, 8 ft.*lbf)



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


6.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.INSPECT FRONT SPEED SENSOR ROTOR
  1. Check the front speed sensor rotor.

    HINT:
    The front speed sensor rotor is incorporated into the front axle hub bearing.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR
OK


8.INSPECT FRONT SPEED SENSOR


    C109455E02
  1. Install the front speed sensor.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)


    C168929E04
  1. Disconnect the skid control ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A15-7 (FR+) - A7-2 (FR+)
    Always
    Below 1 Ω
    A15-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    A15-6 (FR-) - A7-1 (FR-)
    Always
    Below 1 Ω
    A15-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A15-19 (FL+) - A11-2 (FL+)
    Always
    Below 1 Ω
    A15-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A15-18 (FL-) - A11-1 (FL-)
    Always
    Below 1 Ω
    A15-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT SKID CONTROL ECU (SENSOR INPUT)


    C156480E21
  1. Reconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-2 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    A11-2 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


11.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).


NEXT


12.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


13.REPLACE FRONT AXLE HUB BEARING
  1. Turn the ignition switch off.

  1. Replace the front axle hub bearing (Click here).

    HINT:
    The front speed sensor rotor is incorporated into the front axle hub bearing.

    CAUTION:
    Check the speed sensor signal after replacement (Click here).


NEXT


14.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END